"Hello,With the new firmware versions, the motor control was reduced (This produces a big loss of power!You can look at the graph below:Red = input receiver6 = other color out motorsHow to regain power???"
-
Leith Greig
- Male
- Adelaide South Australia
- Australia
- Blog Posts
- Discussions (3)
- Groups
- Photos
- Photo Albums
- Videos
Leith Greig's Discussions
Arudcopter 2.7.3 won't take off .
Started this discussion. Last reply by Thomas Jan 10. 3 Replies 0 Likes
I've just loaded the new Arducopter 2.7.3 in my Octocopter and now it doesn't give the motors enough throttle to lift off the ground . It was flying fine before ; I've calibrated the ESC's again and…Continue
Mission Planner 1.1.92 stays at mav 0.9
Started this discussion. Last reply by Leith Greig Jun 27, 2012. 2 Replies 0 Likes
I've loaded the new 2.6 firmware into my APM 2 and it has MAVlink 1.0 on it . When connecting the board the APM Planner tells me the APM 2 is mav 1.0 and the Planner is 0.9 and to update it to mav…Continue
Leith Greig's Page
Latest Activity
Marooned replied to Leith Greig's discussion Arudcopter 2.7.3 won't take off ."For sure radio calibration is needed as 2.7.3 erased eeprom. I had other strange behavior and radio calibration fixed that.
I'm going to propose some solution to Planner to address such cases."
3D RoboticsChris Anderson replied to Leith Greig's discussion Arudcopter 2.7.3 won't take off .
"Have you gone through the regular setup, including RC calibration? If so, maybe try CLI setup/erase /reset to clean your EEPROM settings and try again."
Leith Greig posted a discussionArudcopter 2.7.3 won't take off .
I've just loaded the new Arducopter 2.7.3 in my Octocopter and now it doesn't give the motors enough throttle to lift off the ground . It was flying fine before ; I've calibrated the ESC's again and no difference .What's going wrong ? See More
Leith Greig replied to Leith Greig's discussion Mission Planner 1.1.92 stays at mav 0.9" . I found it .Thank you ! I should of wondered why there were two Application files .
"
Michael Pursifull replied to Leith Greig's discussion Mission Planner 1.1.92 stays at mav 0.9"Run C:\Program Files(x86)\APM Planner\ArdupilotMegaPlanner10.exe"
Leith Greig posted a discussionMission Planner 1.1.92 stays at mav 0.9
I've loaded the new 2.6 firmware into my APM 2 and it has MAVlink 1.0 on it . When connecting the board the APM Planner tells me the APM 2 is mav 1.0 and the Planner is 0.9 and to update it to mav 1.0 . I've downloaded and reinstalled the software yet the problem still remains . What is going on ?See More
Profile Information
- About Me:
- I work in the film industry .
- Tell us a bit about your UAV interest
- I build rc helicopters and multicopters for camera work .
- Hometown:
- Adelaide
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduRover User Group
207 members
-
Japan ArduCopter Group
58 members
-
Moderators
24 members
-
ArduCopter User Group
1355 members
-
Australia
88 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
