"Seems Ok at 100 meters I would estimate (not measured) in an open space its 200mW so quite powerfull and Xbee is up to 100mW"
-
Nick Goodey
- Male
- CANTURBURY
- New Zealand
- Blog Posts (14)
- Discussions (8)
- Groups
- Photos (20)
- Photo Albums (2)
- Videos
Nick Goodey's Page
Latest Activity
Nick Goodey commented on Nick Goodey's blog post Generate video and OSD with Arduino"Thanks for the tip"
Cadbury commented on Nick Goodey's blog post Generate video and OSD with Arduino"You are probably better off with a MAX7456 as it is designed for graphics. The IC used in the Video Experimenter (a sync separator )is not designed for graphics. You can find an easy to use one here: https://www.sparkfun.com/products/9168"
Jesse commented on Nick Goodey's blog post Generate video and OSD with Arduino"That's ideal to feed back sonar sensor data for when I'm flying by video!! Ordered!! :-D"
Paul Bealing commented on Nick Goodey's blog post Generate video and OSD with Arduino"A year ago I was experimenting with something similar. I modified the DIY OSD by Dennis Frie to send GPS and a bit of other data on 2 unused video lines. I built a receiver that uses a high speed comparator to recover the data and drive a couple of…"
DistributorRC Tech.se commented on Nick Goodey's blog post Small FPV Setup 2.4Ghz
"Yes. But i dont like the affiliate id in the links to HK..."
Stefan Mürzl commented on Nick Goodey's blog post Generate video and OSD with Arduino"My plan was to add telemetry data to unused videolines, because video circuits are much better than audio. Maybe someone reads this and send a mail to me for help."
Stefan Mürzl commented on Nick Goodey's blog post Generate video and OSD with Arduino"You can do much better things with it. For example reading the "closed caption" data.
I worked on a project, but nobody was helping and my knowledge was to bad.
Read more here: http://www.rcgroups.com/forums/showthread.php?t=1672628"
Nick Goodey commented on Joshua Johnson's blog post DroneCafe - The Daily Cup - Blog"Joshua Johnson commented on your blog post "Old Fogey In Coroplast" on DIY Drones
I'm interested in the mini quad in the picture. I'm trying to add some features like voice control to my mini heli and am curious what all…"
Nick Goodey commented on Nick Goodey's blog post Old Fogey In Coroplast"Its a vanilla quad with a KK2.0 board at present here's the build log 20 Minute Quad here is some FPV aroun d the University. I want a auto hover station hold myself based on a an Arduino…"
Nick Goodey commented on Nick Goodey's blog post Kalman Filter Code for Yellow Plane 2"I like the simplicity myself, given the time is available I will be hooking it up to the sensors and then we can see if its cosher, should be interesting "
DeveloperJohn Arne Birkeland commented on Nick Goodey's blog post Kalman Filter Code for Yellow Plane 2
"This kalman implementation looks to be very simplified. Perhaps to much so for a plane? Anyways, it is going to be interesting to see how it compares to DCM."
Nick Goodey posted a blog postKalman Filter Code for Yellow Plane 2
Kalman Filter Code for Yellow Plane 2 Special thanks to Kristian Lauszus, TKJ Electronics This is the code in the main loop UpdateServos()<code>unsigned long msDelta = LastMicros - micros(); LastMicros = micros(); //Measure time since last cycle double dt = (double)msDelta / 1000000.0; // The angle should be in degrees and the rate should be in degrees per second…See More
Nick Goodey replied to Jack Loo's discussion APC220 data drift"Just interested in your over all impression of the APC220.
One thing I need for the remote control is low consistent latency, even without instruments this is easy to see when you are driving a servo from a joystick over the air.
Have a look at this…"
Profile Information
- About Me:
- http://nz.linkedin.com/in/nickgoodey
- Tell us a bit about your UAV interest
- RC electronics engineering and control systems
- Hometown:
- CHRISTCHURCH
Nick Goodey's Photos
Nick Goodey's Blog
Small FPV Setup 2.4Ghz
Posted on February 24, 2013 at 4:30am 3 Comments 2 Likes
200 mW TX on a 120mAh Lipo runs about 30 mins. Total weight with Lipoly 6.2 Grams, only 3.6 Grams with a 5V regulator so it runs of the main battery. The image is not great on a single Lipo cell. I will try it connected to a spare port on the RX see what the signal is like.…
Generate video and OSD with Arduino
Posted on February 24, 2013 at 12:30am 6 Comments 2 Likes
Interesting product if you like me are experimenting with OSD and Arduino FPV GPS Telemeterry
The Video Experimenter shield is an Arduino shield that lets…
Continue Kalman Filter Code for Yellow Plane 2
Posted on January 5, 2013 at 3:24pm 2 Comments 3 Likes
Kalman Filter Code for Yellow Plane 2 Special thanks to Kristian Lauszus, TKJ Electronics
This is the code in the main loop UpdateServos()
<code>
unsigned long msDelta = LastMicros - micros();…
Lighter Yellow FPV Plane 869 Grams Air Frame
Posted on December 2, 2012 at 1:30am 1 Comment 0 Likes
Yellow Plane 2 with inverted V tail software modified and tested stability gyros
Missing battery and camera box have a design which should weigh 140 grams empty.
The assembly shown below weighs 684 Grams no motor or electronics.
Electronics shown weigh 110 grams ESC Arduino board, Xbee, antenna & Gyro…
ContinueComment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduPlane User Group
676 members
-
Moderators
24 members
-
ArduCopter User Group
1283 members
-
Queensland
4 members
-
Taiwan ROC ArduPilot Gro…
8 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
