"Hi SH. The PPM encoder has nothing special in it. Because of its asynchronous design asking for more processing resources (needed for better global compatibility), some rare receivers can cause decoding performance problems, this can induce Jitter…"
-
Steven Tisseyre
- Male
- Essex
- United Kingdom
- Blog Posts (2)
- Discussions (152)
- Groups (1)
- Photos
- Photo Albums
- Videos
Steven Tisseyre's Discussions
Motors spinning on arming
Started this discussion. Last reply by Randy 17 hours ago. 1 Reply 0 Likes
I'm sure this has been asked before, just can't find the answer.Similar to the DJI devices, is it possible to make the motors spin at a low RPM when the APM is armed?I'm sure there has been safety…Continue
Bricked 3DR U-Blox LEA-6 (when connecting JDrones I/O board)
Started Jun 2 0 Replies 0 Likes
I seem to have bricked my second 3DR U-Blox LEA-6 module which is connected to APM 2.5.All was working until I connected the JDrones I/O board,The USB connected to the APM dropped its connection…Continue
Recommendation for Octo Props
Started this discussion. Last reply by Juan Carlos Hdez May 29. 1 Reply 0 Likes
I am in the final stages of completing my Octo with 880Kv motors. I am looking at using full carbon fibre propellors. What would the general recommendation to choose between 12 x 4.5 and 12 x 6…Continue
Rules on mounting telemetry boards
Started this discussion. Last reply by Ted Van Slyck Apr 30. 3 Replies 0 Likes
I'm in the process of building an Octo and laying out the stack plates ready for them to be CNCd.Are there any rules on close proximity of radio transmitters, GPS receivers, XBee telemetry…Continue
Steven Tisseyre's Page
Latest Activity
Monroe Lee King Jr. replied to Steven Tisseyre's discussion Motors twitching in flight"Woah, John where did this come from! Very cool! Thanks I'll have a look at this! The jitter test looks cool."
S H replied to Steven Tisseyre's discussion Motors twitching in flight"I am not familiar with the ppm encoder, but I have found a solution to my random motor twitching and jitter.
After setting the framerate for my RC transmitter from 22ms to 11ms, the problem vanished and it's as if I have a new hexacopter, super…"
DeveloperRandy replied to Steven Tisseyre's discussion Motors spinning on arming
"Not possible yet. It's under discussion so the feature might appear in 3.1.
P.S. I think you might have meant to set the discussion topic to ArduCopter instead of ArduPlane."
Steven Tisseyre posted a discussionMotors spinning on arming
I'm sure this has been asked before, just can't find the answer.Similar to the DJI devices, is it possible to make the motors spin at a low RPM when the APM is armed?I'm sure there has been safety points raised, but I only would like low RPM.Many thanks.See More
Steven Tisseyre replied to Randy's discussion ArduCopter-3.0 ready for wider use"Many thanks for your help.
I've completed the calibration, so will see how I get on tomorrow."
Steven Tisseyre replied to Randy's discussion ArduCopter-3.0 ready for wider use"Excellent work development team, been very much looking forward to v3.0, quite a milestone!
I've quickly just tested the release on my Hex and loiter held well for a few seconds and then I noticed it started to "orbit". This…"
Steven Tisseyre commented on Oliver's blog post Flying Hamburger? Right ..."Nice idea, but i'd have to ask if they have CAA permission to conduct aerial work ?"
Steven Tisseyre replied to Westopher Brownington IV's discussion Twitching apm 2.5"What transmitter / receiver are you using?"
Ted Weerts replied to Steven Tisseyre's discussion Motors twitching in flight"Hi guys,
I seem to be having a similar twitching issue on my copter. I have seen this in flight many times, and it seems to be random. I have an APM2.5 and am running 2.9.1b. It should be noted that I am also using a Futaba T8J and R2008SB running…"
Steven Tisseyre commented on Arthur Benemann's blog post [Update] DroidPlanner v0.8.0"Loving your work Arthur.
Being an Apple fan, I've never had an android device, is there a minimum spec that would be recommended.
I've seen this which is a reasonable price as long as it would be fit for…"
Steven Tisseyre replied to Rigel's discussion CH6_RATE_KP tuning not working"Accepted friends request."
Steven Tisseyre posted a discussionBricked 3DR U-Blox LEA-6 (when connecting JDrones I/O board)
I seem to have bricked my second 3DR U-Blox LEA-6 module which is connected to APM 2.5.All was working until I connected the JDrones I/O board,The USB connected to the APM dropped its connection momentarily when the I/O board was connected. The I/O board is connected correctly and via a proper telemetry cable.Now the 3DR GPS will not power up. No power or fix LEDs.Could it be the case that the firmware is corrupted on the GPS or something more hardware related.Even when connecting the GPS…See More
Steven Tisseyre commented on David Anders's blog post GPS Locator and UAV Rescue"I believe these are even smaller and offers the same functionaility as suggested, plus no need for the printed box.
This is what I use on mine as "asset recovery".
Either use the below link, or search eBay for…"
Juan Carlos Hdez replied to Steven Tisseyre's discussion Recommendation for Octo Props"I have propellers 13x6.5 CF from HiModel and I could not use them because they resonate from certain rpms. With a 920kv leopard lc3542 motor and 4s battery, it was impossible to go beyond 40% throttle."
Steven Tisseyre posted a discussionRecommendation for Octo Props
I am in the final stages of completing my Octo with 880Kv motors. I am looking at using full carbon fibre propellors. What would the general recommendation to choose between 12 x 4.5 and 12 x 6 please. Many thanks, SteveSee More
Profile Information
- Tell us a bit about your UAV interest
- Looking at building my first UAV consisting of a Hexacopter
- Hometown:
- Harlow
Steven Tisseyre's Blog
Anti-vibration APM mount
Posted on April 27, 2013 at 11:00am 12 Comments 3 Likes
I have been looking into my own method of mounting the APM with antivibration in mind.
To this end I wanted to source some freely available components specifically designed to reduce vibration.
I found a couple of such products which I am hoping will be ideal.
These coupled with a custom…
Continue Dome on a Drone
Posted on December 22, 2012 at 5:00pm 14 Comments 2 Likes
I decided that my Drone looked a bit "naked" with all the electronics and flight controller exposed, so decided to have a dome made for it.
Made to measure and a perfect fit having been made from smoked acrylic so you still get to see those all important LEDs…
ContinueComment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Andropilot Users Group
203 members
-
Moderators
24 members
-
ArduPlane User Group
720 members
-
ArduCopter User Group
1355 members
-
ArduRover User Group
207 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
