"I was also under the impression that arduimu V3 would work with ardupilot legacy according to the code. However after a week of troubleshooting I can't get them to work with each other...
If anyone has a fix please share."
-
Tassos Polichronopoulos
- Male
- Porto Rafti
- Greece
- Blog Posts
- Discussions (21)
- Groups
- Photos
- Photo Albums
- Videos
Tassos Polichronopoulos's Discussions
Ardupilot elevator throtle interference?
Started this discussion. Last reply by Tassos Polichronopoulos Dec 24, 2011. 1 Reply 0 Likes
Hi I just set an ardupilot as per the wiki and I was trying to have a simulated flight in xplane (with servos connected) in order to test the setting out but I am getting a strange behaviour.The…Continue
WTB ArduIMU V2 (flat)
Started Dec 12, 2011 0 Replies 0 Likes
I am interested for a used ArduIMU V2, arduino (legacy )shield and thermopiles.Seller should post to europe Greece, payment by paypal.Thanks TassosContinue
ArduImu V3 and ardupilot
Started this discussion. Last reply by Victor Toth Dec 14, 2012. 4 Replies 0 Likes
Is there a way that arduImu V3 can be used with ardupilot (legacy) as a replacement for arduimu V2 that is no longer in production?Thanks in advance TassosContinue
newbie question
Started this discussion. Last reply by Hai Tran Aug 17, 2011. 3 Replies 0 Likes
ok it might sound silly but I finished putting together the ardustation but I have no means of testing it since I have no ftdi cable and no xbee yet, so here is my question, what we are suppose to…Continue
Tassos Polichronopoulos's Page
Latest Activity
Winfried Uphues replied to Tassos Polichronopoulos's discussion ArduImu V3 and ardupilot"Hi Tassos,
did you got a solution for your problem? I also purchased an IMU V3 and would like to use it to replace the thermopiles on my Autopilot legacy. I don´t get the IMU V3 running on my autopilot.
Thanks for your help in advance
"
Tassos Polichronopoulos replied to Dimitri's discussion XBee Pro xsc 900mhz"I am also interested for 2 modules plus antennas,
Tassos"
Tassos Polichronopoulos replied to Steve Price's discussion New to Ardupilot and Need some help! Difference between APM and my setup?"2 wires as on the wiki the one cable was the old method"
Tassos Polichronopoulos replied to Steve Price's discussion New to Ardupilot and Need some help! Difference between APM and my setup?"Steve : wise choice, going for the APM 2 will make things easier.
Luca : upload the 2.7.1 and also d/l the config tool global. and we start from there
"
Tassos Polichronopoulos replied to Steve Price's discussion New to Ardupilot and Need some help! Difference between APM and my setup?"Steve and Luca,
I do have a board set up and although not an expert I can try to help you if you describe the problem.
Steve : I don't think you can use a Joystick with that board to control the plane since the only GCS that support it is HK…"
Tassos Polichronopoulos replied to Tassos Polichronopoulos's discussion Ardupilot elevator throtle interference?"Finally I found the problem , it was my faulty jumber wires............
Thanks Tassos"
Tassos Polichronopoulos posted a discussionArdupilot elevator throtle interference?
Hi I just set an ardupilot as per the wiki and I was trying to have a simulated flight in xplane (with servos connected) in order to test the setting out but I am getting a strange behaviour.The throttle seems to be interconnected with the elevator, so when I move the throttle on the TX the elevator servo moves also.Any suggestions will be greatly apreciatedTassosSee More
Tassos Polichronopoulos commented on Chris Anderson's blog post Details on how Iran may have used a GPS override spoof to capture US drone"Makes sense, cut comms, drone goes into RTL mode, fake GPS signal to spoof landing site.
"
Tassos Polichronopoulos replied to Tassos Polichronopoulos's discussion ArduImu V3 and ardupilot"Hi Chris , thanks for the answer, I thought that ardu IMU V3 is current gen hardware that was a direct replacement for arduimuV2. If it's not to be used for Ardupilot then what is ment for since APM doesnt need an IMU?
Thanks again Tassos"
3D RoboticsChris Anderson replied to Tassos Polichronopoulos's discussion ArduImu V3 and ardupilot
"Yes, you could probably modify the code to do that. But that's something the community should do--the dev team is no longer supporting the legacy ArduPilot and is focused on current-gen hardware. "
Tassos Polichronopoulos commented on Hai Tran's blog post Ardustation 2: Antenna Tracking, Mavlink, Flight Data for Arducopter 2"Well the reason I am asking is that I am fixing my own tracker and I was wandering what servos to use in order to be compatible with the ardustation software. I tried last night with a modified 360 servo and the ardustation would not open the lcd,…"
Tassos Polichronopoulos commented on Hai Tran's blog post Ardustation 2: Antenna Tracking, Mavlink, Flight Data for Arducopter 2"Hi do we need normal servos for the pan tilt or modified ones for 180 or 360?
Thanks in advance
Tassos"
Tassos Polichronopoulos commented on Bob Hern's blog post Turnigy 9X IN STOCK at the US Warehouse!!"HI can you please provide a link for the diy Frsky mod for the 9x?
Thank you in advance"
Tassos Polichronopoulos commented on Chris Anderson's blog post Anybody recognize this drone?"hell why one of these birdies can't crash in my backyard , I need a new flir camera ;)"
Profile Information
- About Me:
- Just interested in UAVs
- Tell us a bit about your UAV interest
- Interested in UAVs and anything that has to do with flight in general.
- Hometown:
- Porto Rafti
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduRover User Group
184 members
-
Documentation Editors
51 members
-
ArduPlane User Group
682 members
-
ArduCopter User Group
1288 members
-
Andropilot Users Group
182 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
