Todd A. Lloyd
  • Male
  • Huntington, WV
  • United States
Share Twitter

Todd A. Lloyd's Discussions

Pitot tube for IMU

Started this discussion. Last reply by Todd A. Lloyd Jul 17, 2010. 2 Replies

Hey Guys, I was wondering how the air speed sensor is hooked up to the APM shield.

 

Todd A. Lloyd's Page

Latest Activity

Todd A. Lloyd posted a status
"have most of the parts. need tubing and fuel, then it'll be started up around spring"
Jan 29
0 Comments
Todd A. Lloyd posted photos
Thumbnail
Thumbnail
Thumbnail
Sep 26, 2012
Todd A. Lloyd posted a status
"getting closer to finishing my plane"
Sep 13, 2011
0 Comments
Todd A. Lloyd posted photos
Thumbnail
Thumbnail
Sep 13, 2011
Todd A. Lloyd commented on Max Levine's blog post ArduPilot/Copter Mega 6 position 'mode' switch for FlySky/Tunigy 9x/ and others.
"will this setup work with the Futaba 6ex?"
Jul 15, 2011
Todd A. Lloyd commented on Martint BuildYourOwnDrone.co.uk's photo
Thumbnail

The Fleet............

"looks good  "
Jun 11, 2011
Todd A. Lloyd commented on Jean-Louis Naudin's blog post Full autonomous Cularis UAV mission with Ardupilot/ArduIMU
"really enjoyed the videos  "
Apr 16, 2011
Todd A. Lloyd commented on Kirill's blog post ArduPilot Mega Instructional videos
"good to see this  "
Mar 25, 2011
Todd A. Lloyd commented on Corey Upton's blog post UAV for High School Senior Project
"sounds great  "
Mar 21, 2011
Todd A. Lloyd posted photos
Thumbnail
Thumbnail
Thumbnail
Jul 18, 2010
Todd A. Lloyd replied to Todd A. Lloyd's discussion Pitot tube for IMU
"Thanks Chris, that gives me a starting point"
Jul 17, 2010

3D RoboticsChris Anderson replied to Todd A. Lloyd's discussion Pitot tube for IMU
"We haven't enabled that in the code yet, but the physical connection is via the three pins marked "pitot" on the shield, next to the I2C port. The three pins are marked GND, V+ and IN on the bottom of the shield."
Jul 17, 2010
Todd A. Lloyd posted a discussion

Pitot tube for IMU

Hey Guys, I was wondering how the air speed sensor is hooked up to the APM shield.
Jul 17, 2010
2 Comments

Profile Information

About Me:
I'm an electrician, and I'm into model planes
Tell us a bit about your UAV interest
I would love to design my own UAV someday
Hometown:
Milton

Todd A. Lloyd's Photos

Loading…
  • Add Photos
  • View All

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Social Networking

Top Content 

1 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
2 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
3 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
4 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
5 ArduCopter-3.0 ready for wider use

ArduCopter-3.0 ready for wider use
6 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
7 Drone shot down by police

Drone shot down by police
8 MAAT final version is being tested

MAAT final version is being tested
9 Getting ready for Arducopter 3.0

Getting ready for Arducopter 3.0
10 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service