Is it possible while running one ground station, to control 2-3 drones simultaneously?
Here I go with a inicial research of airframe with a universal fuselage, that can be
used with different wings. I am interested in UAV lifted way high by a balloon and
then glide down , similar in shape like spaceship 1.
How do you get Google to NOT show old GCS runs ? My display is unreadable now.
Earl
I have a question about the Li-Po battery options for the upcoming Arducopter quad kit. I was reading the Aeroquad tutorial to get an idea of what I should buy and they recommend using the HobbyKing 4400 mAh for the Aeroquad. However, I have seen som
Read more…3rd flight with APM on-board today, only the 2nd time I've turned it on while in the air.
Just a small note that I was able to use the Ardupilot Mega in an experimental setup with FlightGear. I ported the XPlane 0.43 software to Linux C (using autotools). The trouble was finding out that a simple "usleep" wouldn't cut it, but that reading
Read more…Am trying to start a Quad rotor Helicopter with Arduino Pro + ArduIMU. Please provide me with Arudino code. I have planned to use only ArduIMU with its native code, can anyone make it to extended Kalman filter for better stability.I need to have a si
Read more…SO i've been planning on useing Mgea for my uav, seeing as it offers the most bang for the buck, andthe most features, ext.
Has anyone had any issues with using an eflite brushed ESC? I have a 20amp one installed in my HobbyZone SuperCub LP and the APM constantly resets itself by power cycling. I also have issues with the APM freezing on the control surfaces for a second
Read more…I plan to make frame with Trex 600 tailboom and 3mm plywood.
A
|
|
|
B ---------Center--------- C
|
|
|
D
I plan to use Turnigy 221
http://code.google.com/p/ardupilot/issues/detail?id=6
Hi all,
1. I downloaded ArduPilotMega_1_0_1.zip and GPS_IMU.zip to use
#include <GPS_IMU.h> // ArduPilot IMU/XPLANE GPS Library
and
#define GPS_PROTOCOL 3
The compile was successful.
2. I downloaded Flightgear 1.9.1b, and copy xml protocol file into
C:\
Read more…Hi all,
I'm about to start a project on making my first autopilot! From what I've read so far, thermopiles are fairly accurate and not susceptible to noise such as vibration whereas the IMU is. However, from most autopilots that I've seen, neither ar
Read more…Some questions ...............
I’m in the early stages of investigating different airframe possibilities – looking at the pros & cons of different layouts, shapes, sizes, wing profiles etc etc ……… which inevitably leads to a whole bunch of questions
In
Read more…Hi guys, I recently bought myself a gyro & accelerometer to use with my Arduino Duemilanove to calculate roll & pitch. I read that I need to use Kalman filters etc but can't find any sample codings of how to use it, does anyone have any samples or ti
Read more…Hello all I'm new to the site.
1. I have just got my APM setup and have tried the test code for the RC input and I'm only seeing 1200 on all ch with the TX on or off I would think i would see some noise or something even if I had RX issues but the RX
i currently have a ardupilot mega board, brushed motor n ESC..I have connected brushed motor to the ESC. From ESC 3 wires to the output (OUT0 pin) of APM. I would like to know how to programme the ESC in order to control the speed n direction of the
Read more…I have done many hours of surfing the web to find a video transmission system that is
A: Not 900mhz or 2.4ghz so it will not interfere with Xbee or my Futaba 6ex Radio
B: Long Range, 3-4 miles
C: Under 140g (save weight for batteries)
D: Good Quality (m
This is our first post on DIYDrones, where, I hope, we'll be relating our experience about building and crashing our first Easystar model.
