Hi,
I am busy building up a new Y6 and noticed a very strange thing. Every flight (only about 4 of them) I have done with this standard 3DR Pixhawk and GPS/Compass module so far I get DGPS lock (GPS_STATUS = 4).Mission Planner also starts out with "No
Read more…hi developer
I have tuned the AHRS_YAW_P value to correct the heading drift.
I set this parameter to 0.4(the max value adviced).
I wanna know if it is OK when make AHRS_YAW_P more than 0.4.
The function of this parameter is the same as P controller for
Read more…Hello Everyone,
I am also writing this post because I need something, and I think its possible to do. Recently I attached the new Ronin MX, A Hyperspectral Camera, An Intel Nuc to a DJI S1000. Needless to say, the payload was around 14 - 15 pounds wit
Read more…Hello Everyone,
I am also writing this post because I need something, and I think its possible to do. Recently I attached the new Ronin MX, A Hyperspectral Camera, An Intel Nuc to a DJI S1000. Needless to say, the payload was around 14 - 15 pounds wit
Read more…Includes (see itemisation below for details):-F550 Clone Hexacopter with loads of extrasNighthawk 200 Quadcopter with loads of extrasIMax B6AC Charger capable of charging all the batteries includedTurnigy 9XR RC Controller inc Battery and Transmitter
Read more…A foundry service is offered to Customers to exploit the FOGPHotonics Integrati technological know-how in LiNbO3 processing for integrated optical circuits.Customer uses the service to get processed wafer, polished and diced circuits as well as pigta
Read more…Hi, I am selling a brand new Precisionhawk Lancaster III Rev 04. Here is a link to the ad on ebay: http://m.ebay.com.au/itm/PrecisionHawk-Lancaster-III-Rev-4-Ag-UAV-Drone-from-just-AUS-9250-/112087877970?nav=SELLING_ACTIVEAny questions, give me an em
Read more…Hello,
I am using ArduCopter 3.3.3 as my firmware and Pixhawk as my autopilot.
How do I output the command GPS_RAW_INT out of Serial 2?
The camera I am trying to output to is interfaced for Mavlink protocol.
In the Mission Planner GUI, I cannot configur
Read more…HI ALL
I use the DJ airframe and pixhawk .
Tune the PID by autotune firstly,and the use the channel6 knob for the detail.
And do the compass carlibration OK.
Stabilise Althold Auto modes are all ok.Loiter is OK when hold the position,But when I pitch the
Read more…Hello everyone! I am new to pixhawk. I am trying to do a Hardware in the Loop Simulation using pixhawk and xplane as discribed here. I am using QGroundControl as my GCS.
What I have done:
Pixhawk Connections:
I have connected pixhawk to my computer thro
Read more…Hello,
I'm using an ArduPPM converter with betaflight.
I need values from 1000-2000ms but if I configure my radio so it does that. The PPM-Encoder marks it as failsafes and puts out the failsafe values.
How can I change the critcial values? I have alre
Read more…Hi all,
I am trying to connect my arduino uno to the pixhawk to control two servo motors of my rover. I am new to this and trying to figure out how to go about this.I have looked at some posts suggesting to use serial. I am little lost and can really
Read more…So im pretty new to all this stuff and im just curious where a good place is to start with my project.
Heres the Details:
I have an "Accelerator Protocol" Helicopter that I would like to have do an automated Flight path, I mostly want to create this fo
Read more…Great condition Event 38 E384 complete mapping package with Canon S110 RGB and S110 NDVI cameras, 2 extra batteries, 915Mhz long range telemetry package. More info can be found at Event38.com. About a year old, flown twice just never had time to comm
Read more…Hi
Has anyone had a go at getting the Mobius action cam with its docking station and a smart phone to work together for FPV
Read more…Greetings to all of you!
Today is a nice day for a discussion. And would like to dhare with you by an interesting article about one quadcopter. It may be useful for every modeller.
http://www.rcfair.com/blogs/view_entry/12638/
Hi All
I am wondering if someone can point me in the right direction to diagnose why my Arducopter 2.6 F450 suddenly dropped from the sky and crashed.
I have the latest log but being pretty new to APM and Quads, I just need some pointers on where to lo
Read more…Hi, I am new to the hobby and have ran into a problem involving the ESC's. I bought the Andoer 30Amp ESC and calibrated it for the GoolRC A2212 1000KV brushless motors. These two parts were previously used on another quad copter so I know they work
Read more…Toward the end of this year, I will be building an octocopter for someone. I want to use pixhawk as it is the most advanced of all FCs.I have built small AP quadcopters before, so I do have some experience.The connex system wil allow for a second use
Read more…
Hey guys!
I hope I'm right here, because I dont knwo in what category it fits better..
Well I have an M8N GPS that didnt worked out of the box with my pixhawk.
I got no GPS signal at all.
So I used a USB<=>Serail bridge and connected it directly to the