I had a crash with my hexacopter with pixhawk 3.3.2 firmware
I had a perfect flight until i loose my front left prop as you can see at the video.
After the prop break from the hub the copter still hold it possition and stability
I dident understand why
Read more…I had arducopter plugged in and connected to mission planner via USB. I kept getting a warning that the battery voltage was low.
Generally speaking, a GNSS RTK board will provide various electronic interfaces for communication as below.
- COM1/COM2, employ 5pin PicoBlade receptacle connector with TTL voltage level (1.25mm inter-pin distance)
- LED Indicator, shows the operationa
Read more…Here's a link to a video I did explaining how to set up Flight Modes on your Aux switches on the FS-I6. This should also work with the Turnigy TGY-I6.
When I looked around the net I couldn't find an explanation on this particular RX, so I hope this he
Read more…While flying several circles with different radius (in Auto_mode with the command loiter_turns) my vehicle starts losing altitude when it has a speed of 10 m/s. The first idea was that this was caused by the aerodynamic effect that causes the baromet
Read more…i am using a dx18 transmitter......i want to implement a custom built varying frequency input signal generated using matlab on my rc. does anyone has any ideas.., please suggest
here is an example signal in the image
if there is a way to use such a sig
Read more…Hello there.
I'm new to the drones so I wonder what's option is better: buy all-in-one Phantom 4 or assemble my own drone?
Read more…I modified the code (AC 3.3.2) to support switch to FLIP from LOITER.
Most time, it did pretty well. The copter switch to FLIP from LOITER and back to LOITER.
However, this time, when the copter switches back to LOITER, the copter flied to the south mo
Read more…Hi All, (Quad PixHawk 3.3.3 >> MP 1.3.37)
I realize that this may be a trivial question to those
who have their own Calibration techniques well sorted,
however, my question is -
During the Accel Calibration procedure -
One is prompted to
Read more…Hello,
I just wanted to start a post discussing AC3.4. People should be aware that I'm not reviewing the code in Master or doing test flights at this time. Recently, a large set of changes went into Master related to refactoring the flight stabiliza
Read more…Hi all,
I was able to connect my pixhawk px4 to Mission Planner and update to helicopter airframe. I was told that QGroundControl was better but I only see a coaxial helicopter setting and no conventional helicopter. Anybody know why that may be?
Thank
Read more…So, I'm obviously a little lost here. I have sets of the jDrones v2 RFD900+ radios. I cannot get them to talk to each other. They had all of the same parameters on the SiK radio page in Mission Planner. When I was messing around with the settings
Read more…Hey, I'm relatively new to the whole Quadcopter/Hexacopter thing.
I recently built a QAV250 with a APM 2.6 flight controller as a test setup before making the plunge and moving my F550 over to the APM.
The issue I'm having is when ever I come out of s
Read more…I have a 3DR X8+ and I need parts for it. The 3dr website gives 404 errors left and right, and I can't seem to find a supplier with the parts I need. The chat on 3dr's website is constantly unavailable and email's don't get answered. I don't even
Read more…Hi,
I bought it last year
It's in NIB condition
Never used as I didn't have time for my project
Selling it with needed cables set
Price : $135
By Paypal
Buyer pays for shipping fee
Regards,
JC
Read more…I have a couple questions about how Arducopter handles the X4 configuration vs the X8 configuration. What are the differences? Is the X8 the same as an X4 with identical signals sent to the top and bottom motors? Is there anything special happeni
Read more…Hi,
i am using a vibe 50 nex helicopter setup with a DX18 transmitter and pixhawk. I am using this for research and analysis purpose. I am trying to use pixhawk as the controller. Done the regular firmware with the latest version. I have disabled the
Read more…Hi All, ( Quad PixHawk FW 3.3.3 MP 1.3.37)
Is there a method one can use to determine a craft's COG state, or how
well the craft is balanced?
I am not sure if this is documented somewhere?
If so, please point me to the correct info?
I was thinki
Read more…Hey guys,
I'm looking to get 2 custom built frames built that can fit a few sensors including the SF40/c LiDAR on top of a gimbal. I'm looking for something either on the lines of the Aztec Firefly (carbon fibre w/ plastic hood) or a design like the M
Read more…