Hi,
I was doing some tests today with an APM 2.5 and discovered that the pressure sensor was reading continously decreasing values (see attached image). This may be because of a sensor failure or because of some parameter that is not correctly set in
PASSED AT RESOLDERING TEENSY DF13 CONNECTORS
Read more…I have a pixhawk with all the accessories (GPS, Data radios, OSD) and I'm powering through the power port with the servo rail as a backup. How many amps is the power port going to draw? I have this bec that only outputs 1 amp with a max of 1.5 amps.
Read more…As soon as I put my Y-6 (arducopter 3.1 on APM 2.5) it begins to slowly rise. Even if I continually lower the throttle (which should reduce the targeted hold altitude) it still climbs. I think my vibration level is OK (generally <1). Here is a log
Read more…
I had a GPS Tracker on it and actually was able to retrieve it without damage.. I do not have a good understanding of the logs to interpret them yet.... Can someone take a look at the log attached and see what might have happened?
I will be very grate
Read more…Had a runaway.
I had a GPS locator on it so I was able to find it. A small cypress tree caught it for me, so It was treated gently.. no damage.
Looks Like I had some serious vibration at full throttle. I don't think that was the entire reason though, I
Read more…Hi all,
I have a quadcopter based on APM 3.1.5. It flies just fine in stabilize mode. It flew also great in auto, loiter and alt hold modes - everything worked perfectly. I have now changed the cheap plastic props for some CFK props (which I balanced
Read more…Hi,
I would like to move my pixhawk between 2 different models, how do you backup all settings and configuration for one drone to allow the moving of the board to a different model, and later when its moved back how to restore all settings and config
Read more…Correct me if wrong, but when doing a continuity test (power lead and motor shaft), there should be no reading.....OL.
I posted what I thought was possibly a bad Pixhawk at Arducopter support forum. It had me puzzled because the initial testing didn't
Read more…Another crash caused by a switch to a different flight mode....
After several good flights with my pixhawk equipped quad, i had a crash soon after take off immediately after switching to alt hold flight mode. The quad immediately rolled over and fell
Read more…Hi to everyone,
someone of you knows if and where I can download the CAD model of the IRIS Quadrotor?
Thanks in advance,
Fab.
Read more…Hi to everyone,
I am using an IRIS quadrotor and I noticed already one thing that I don't like too much but I think there should be an explanation for that but I would like to know if someone of you knows more.
Why is it not possible to have a switch
Read more…My Pixhawk boots fine when powered by the power module only, but when I connect 5V to the servo/motor output rail, it doesn't boot but just makes clicking sounds instead.
Video demonstrating the problem:
https://www.youtube.com/watch?v=jODj9UzkG1Q
The
Read more…Hi,
I am having difficulty compiling ArduCopter 3.2 using eclipse.
Compiles using, cygwin in the SITL target but does not compile in apm2 target.
With eclipse, I am having trouble giving it the arduino path.
Setting path variables in eclipse:
SKETCHBOO
Read more…Finished my y6 kit this past weekend, have been having some fun flying it for the last few days. This is my 6th flight or so. But it ended in mild disaster. After flying it around for a bit, I was flying it down low about 6ft off the ground and 15 fe
Read more…Hi to everyone,
I am a PhD student and my lab has an IRIS quadcopter. I was wondering if is it possible to fly indoor with it or not? Even if it is needed some kind of hack.
Thanks a lot,
Fab.
Read more…Hi all-
This is my first foray into, well building anything (besides dorm room shelves)... I've got my copter all assembled, but am having a really hard time getting it to take off. I've checked out the troubleshooting page, and re-calibrated my ESCs
Read more…http://vancouver.craigslist.ca/rch/for/4687569095.html
I'm about to buy this kit to put an ardupilot inside. Can anyone with experience confirm this is all I'll need to build my arduplane?
Please reply asap I'm supposed to meet the seller very soon.
Read more…I'm been searching and reading (even in Github), but haven't found any definitive answer(s) yet.
Is this something that is already supported or is it in a todo queue somewhere (which I can't find)?
The manual refers to PWM RSSI. Unfortunately, there ar
Read more…I just started using Adobe Warp to smooth out my aerial video and am impressed with the results. Don't know why I wasn't using it before, as I've had Adobe Creative Suite with Premiere Pro and After Effects for a couple years. Anyway, I made a shor
Read more…