Hello,
I had a crash today with my Skyhunter running on 3DR Pixhawk with latest firmware 3.1.1.
I don't know why but after review of a tlog it seems I lost telemetry signal for a few seconds and then RTL mode switched over resulting in a crash because
Read more…Hello everyone
2 accidents today and maybe same (human) error.
I was trying long auto mission - 2 km from home - and for all the 2 missions, when the drone is going back, I get an RTL and a stabilize and the drone fall.
I have un TX9 XR + RX Frsky and f
Read more…Hi folks,
I've just changed my APM2.6 to a pixhawk and noticed the motor test is out of sequence which is a bit confusing.
Normal motor test spins motors in turn from "front and right of centerline and clockwise around the frame"
I am getting them spinn
Read more…Logo400 and Pixhawk, here a short movie of some initial testing
https://www.youtube.com/watch?v=XWkMkfvdQD8
Read more…ArduPlane 3.1.1 not working proper on flying wing any body else facing problem as soon as switch on to fbwb or auto mode it nose dive and roll on one side.
Read more…Hey everybody,
I was wondering if anybody knows whether or not you can use an airspeed sensor with arducopter. As I understand it, with arduplane, the airspeed sensor acts like a barometer as well. And if so, I was wondering could an airspeed sensor p
Read more…Hi
I'm trying to performing geotagging photo in MP on my UAV (x8) using a Home made chdk cable for canon (A470) i Use chdk 1.2 with a script KAP UAV ver 3.2 . . I use Pixhawk , the home made chdk usb cable is done using HK led control cable. Ever
Read more…Perhaps one of the developers could chime in here. I have a question as to whether AutoTune will work well with a platform that weighs almost 20lbs, uses 100kv motors and swings 28inch props. I have not seen any documentation on performing an autotun
Read more…I had a scary experience today using loiter. I had the quad about 3 metres off the ground and switched from Loiter to Stabilize and the mid throttle position did not provide enough thrust so the craft came to ground too fast for me to adjust. Fortuna
Read more…Just started building a Tarot T810 with Pixhawk FC
I've only been using Naza before but decided that the Pixhawk will be a better choice for this hexa.
Here is the parts list so far
Hi,
What's your feeling about this one :
Canon IXUS 155, 20 M pixels, 142 grams, no CHDK yet, but "Continuous Shooting Approx. 0.8 shots/sec. (until memory card becomes full)"
For a fine 20M picture, 7 Mb, that is more than 2000 pix in a 16G memory card
Read more…Hello,
I got my plane working good, FWBA works , RTL works , Loiter works. These are the only modes I use right now.
I am interested in auto take off. Do I have to setup a full mission for auto take off or can I just set mission to take off alone witho
Read more…Hi all, I had an idea the other day.
In my experience, flying FPV has always been so difficult to control and judge where you have to be in order to not run into stuff and to determine changes in altitude. OSDs help some, but it's still difficult to j
Read more…I am building a Back to the Future car/drone that has EMFs as the hubs of the wheels .
I saw Ed Kirk's Scarab Quad video and figured that I could build the fans into the wheels just like in the movies.
I already have a prototype wheel/fan unit that
Read more…Hi
is there a way to interface the Pixhawk with a Spektrum telemetry module?
To receive telemetry data from the Pixhawk on my Spektrum RC display?
Felix
Read more…Heard this on the news this morning in Dallas. I love how the story describes the UAV in question as apparently being a flying wing, but they use a stock photo of a Phantom quadcopter.
http://dfw.cbslocal.com/2014/10/07/faa-dallas-police-investigati
Read more…Hi,
Is there any way to download data flash logs in droid planner using usb cable? Or is there any other android app which does it?
Read more…can somebody help me figure out what went wrong with my quad? It was on its last leg home, and it freaked out and speed out of control and crashed pretty hard. I turned off the remote when I realized it was going the wrong way fast, hoping failsafe w
Read more…Hi folks,
I've been doing research into learning how to access offline maps in droidplanner 2 on my new android device.
I'm completely new to this android operating system but have gotten the hang out droidplanner 2.
My current issue is offline maps. I
Read more…Hi group,
I had a crash with my Skywalker into a high voltage transmission line (110kV?).
The plane had only minor damage to the canopy.
But the MediaTec GPS seems to be broken. No longer working.
Yesterday I tried a manual flight and everything works fi
