There are probably answers to questions below since DIY Store sales Spectrum Transmitter but I can't find them.
Could I get some help.
-Is it a procedure to connect and bind a Spectrum satellite on the APM2 ?
-Do we need to load software(s) for PPM enco
Read more…I would read this to get familiar with the basics of the airspace structure... :
http://www.aopa.org/asf/publications/sa02.pdf
...and I would also check this:
Read more…Hi everyone !
My first quadcopter is finish to build and I want to test the motors with the "motors" command in the CLI.
The wiki say (after enter the command in the CLI):
Plug in your LiPo battery and connect the four-wire cable from the Power Distrib
Read more…Hi All,
I just wanted to give everyone who is waiting for a 3DR 433MHz radio a heads up about a shipping delay. A few days ago I discovered an interference problem with the 3DR 433MHz radios that can cause the range to be much less than expected. We'r
Read more…Quick FYI, if your wondering if the Easy Star Electronics Chassis fits the new EasyStar II.....it seems to fit just fine. Not as nice a fit as the original EasyStar but fits without any modification and with a bit more room available. Couple of pics
Read more…Is there a time frame for when you think the XBee footprint version will be out? I finally got around to ordering an APM2 and got an "Air" module of the new radio but now am wondering if I should have held off on the single radio as it will be fairly
Read more…Hi all...
I'm wondering if I can add dragonlink RSSI connection to the APM1, and have it report in the MAVlink stream to the minimOSD.
Not coming up with much in my searches.
Thanks
JC
Read more…I booted APM - now with stock Plane 2.33 firmware - but this problem existed for a very long time.
Altitude = 0 (real altitude is less than 20meters.)
waited for GPS fix.for several minutes.
Altitude is now 82 meters. (the moment that GPS got fix.)
reb
Read more…We've just released ArduPlane 2.33 for your flying pleasure!
This release adds three new features over the previous release:
Hey guys,
Has anyone ever tried to tilt/angle the rotors to help stabilizing the aircraft? If you look at De Bothezat design, it does use this principle. Here is a picture illustrating the concept:
Once I calibrated compass - how/when would I recalibrate it ? or is it only done once per hardware configuration ?
Would a recalibration be needed when flying on a new site, or after some time ?
Read more…Hi,
I have successfully tested my software with the new MPU-6000.
So the old sensors that i used are for sale.
MPU-6050 breakout
IMU-3000(ADXL345 & IMU3000) with HMC5843
If you are interested contact me.
Hi all,
I cannot see any green bars to calibrate radio signals (AC quad, new APM2 board, Mission Planner, win xp)
do you have any hints for me to debug or solve?
board has gps lock.
My thought is that the Mavlink comms is faulty one way (sending to APM d
Read more…I know I have firmware 2.30... 2.32 , how can I verify it's version number ?
Read more…It has been a couple of weeks now and I'm getting more comfortable with my STABALIZE and LOITER set up on my 3DR quad. Still having some yaw issues but yesterday morning I was enjoying the fruits of my labor out at my local RC field.
In one of my last
Read more…One thing that I liked about the xbee air unit was its tiny wire antenna.
Are there other options for the air unit besides the right angle antenna?
Read more…There has been a lot of discussion about regulatory compliance on the announcement thread for these radios.
I thought I should explain a bit about why these radios don't already have compliance certificates, and what you can do to get involved in an e
Read more…If I wanted to move the radio away from the APM2 (mounted onto a wing, for example), are there any limitations on the wiring distance between the radio and APM2?
Read more…apm1 3dr running in X. well i was flying it and i landed hard, went to refly it and now my controld are reverse.... i push stick right it banks left, i pull back it goes forward....Hmmm anyone seen this before?
Read more…