Hello,
I was working on my Delta drone yesterday. Connected a Pixhawk Cube to it.
I was just testing the operation of the control surfaces. For that, I turned the AUTO Mode ON. Checked the Elevons, working fine. Both, Elevator and Ailerons. This is w
What are some commercially available lightweight drones which can be programmed (Micro or nano size) with as many builds in sensors? I want to implement machine learning algorithms. Please suggest if there are drones under 250 USD.
Read more…Hello DIY Drones community,
I'm seeking some assistance trying to figure out the source of wobbliness on my Hexacopter. I've attached the log here. What happens is the drone will take off and it seems relatively stable. I can generally make gentle
Read more…Hi,
I am selling several brand-new GNSS high precision heading board with low price ($400/each, the original price is $650/each), and below is the description of this product:
UB282 is GPS/GLONASS dual-system dual-antenna board for precise RTK position
Read more…I'm flying the latest FW on a PixHawk and need a PWM signal that (preferably) is the average of all the other PWM (Servo) outputs. I flying a quad, so Servo 5 is available.
In MP, there is an option to set SERVO 5 to "Throttle" using option "70", b
Read more…I am trying to send throttle command with ROS node using mavros and publish messages to topic [mavros/rc/override] but I am not getting any response from drone in gazebo simulator.
Read more…How to control the height consistency of brushless motor stator core laminations
As we know, When the BLDC motor design is high speed and high frequency with high efficiency target, a thin silicon steel (such as 0.1mm,0.15mm or 0.2mm) will be much ben
Read more…Hi,
I have seen some rules in uav competition that when entering failsafe mode, the vehicle must:
- Throttle minimum
- Altitude maximum
- Rudder full starboard
- Aileron full starboard (port)
- Flaps fully extended
I didn't understand it at all. I just know
Read more…Dear Aerial photographer,
We have updated our X30 optical zoom camera. We want to find more friends to test this and establish further cooperation. If any interest, please reply to this post and send me your contact information via private messages. M
Read more…Good day,
I am building a ground station for Mavic Pro. I have the basic plan, but I don't know the wiring aspect. Please, I am not to experience with electronic aspect.
OK this is the basic...
Pelican style case, about 24 x 18 inches. Bottom will be
Read more…New build shakes like hell. Why?????
1. Checked motors direction.
2. Tried different props.
3. Flashed different bheli firmwares.
4. Tried changing ESC protocols. Dshot300, 600, multishot etc.
5. Noted that motors do not spin equally in Betaflight
I have been trying to plan a mission and the emulator multi copter ( drone icon ) home point is in Switzerland. How do I update the emulator to my current location? I've tried changing the GPS coordinates manually but no luck. I've also tried ignorin
Read more…Is this the solution of hybrid multirotors?
4 centered gas engines to lift the most of the AUW, say, around 70% the remaining 30% is lifted by outer smaller electric engines.
4 center gas engines to cancel torque and have enough lifting power (gas en
Read more…Hello to all!
I don't belong to many forums but I've known it to be customary to introduce yourself upon joining. I didn't find an introduction thread so I figured I'd post here.
I changed my screen name to help avoid doxing. There are just too many
Read more…Hi,
I am developing a drone using the nvidia jetson TX2 module for survey purposes and i am searching for suitable carrier boards and flight controllers for the module that are most re commendably used on drones
thankyou.
Read more…Hi all
Greetings from Borneo. I am trying to install QGC 3.3.2 on a Mac Air running OS10.9.5. Every time I boot up the programme I get a Qgroubndcontrol quit unexpectedly error message. I won't copy and paste the entire message but the text below shou
Read more…Hi all, I want to get help on a problem I have been facing since updating from copter 3.3. I have a TBS Discovery with a gimbal that I like to use for mapping and aerial footage. When mapping I fly the quadcopter in auto mode with a grid flight plan.
Read more…Hello
I am working on a land restoration project, and we would like to distribute seeds from a drone.
I hope to find a way of calculating a rough distance from the Drone dropping point (projected into the ground) to the landing point. This can give us
Read more…Hello everyone please,
I have a 3D printer but I do not have a schema,
where can I find a 3D Printed Anti-Vibration Platform for pixhwk
thanks :)
Read more…
I am doing my EPQ which is a school project and I am making a quadcopter for it. I have designed what I want it to look like in 3D and theres an image attached. I want to make this frame but I dont know how. I know I could probably pay a company to p
Read more…