I can't get QGroundControl to work ever on my Mac... Trying to install the latest 3.3.2 version on a Mac running OS X 10.9.5. Would love to hear of any solutions. Each time I try to boot it it crashes half way through the boot.
Read more…Hi!I have started my first custom drone setup and stuck on ESCs calibration.I am using Pixhawk 2.4.8, my RCS is RadioLink AT9S, R9DS receiver is connected to flight controller via SBus, ESCs are Turnigy MultiStar 30A BLHeli-S Rev16 V3. I upgraded Pix
Read more…I'm using the latest PixHawk firmware (I believe it is 3.5.5), and I want to adjust some parameters that don't appear in MP at all. This is a multirotor quad.
For example: In the SERVO FUNCTIONS, MP has options 0-80, yet in the ARDUPILOT ORG "docs",
Read more…Hi everyone,
I am a member of student research group, which is builing a drone (hexacopter). It’s our first drone, so we haven’t got actually any experience in this field. We base on APM 2.8 and we want to connect Nova Fitness SDS011 sensor with Ardup
I am trying to increase the sampling rate of the DataFlash logs being saved to the MicroSD card on Pixhawk. (Primarily raw IMU data). I'm using a Pixhawk 2 board with Mission Planner and QGroundControl.
I can't figure out how to use "sdlog2" consideri
Read more…I'm new to MavProxy (and to MavLink data in general) but just succeeded in installing it and running it interactively on a Raspberry Pi physically connected to the Telem2 port on a Pixhawk2.1/Cube. My question now is how I can non-interactively (an
Read more…Hi,
I have build a small quadcopter which I want to use for low quality/high risk mapping tasks. Unfortunately the Raspberry Pi camera shows extreamly high jello, there are serveral horizontal stripes going through the picture.
Has anyone experience ho
Read more…Hey, everyone. Here is the TFmini LiDAR working well under very bad environment.
Objectively speaking, I think highly of this tiny guy against bad environment.
And here is the comment of the client who took the picture.
TFmini matches drone very wel
Read more…Imagining that a high frequency TF02 lidar in a drone help to count record the car flow.
For details contact bw@benewake.com
Read more…I just received a 3-Axis gimbal with a Storm32 controller. I loaded the GUI and find that the board has version 090 firmware. The board is V 1.3.
I can read and write to the board with the GUI. I put a camera on the cradle and attached a 4S battery
Read more…Hi Guys,
Its been a few years since i have been on DIY. The company i work for is starting experiment with Autonomous flying. A question asked was "What are the most common mistakes made by people using Pixhawk or any version of..pixfalcon etc.." Is i
Read more…Hey, everyone. Here is the TFmini LiDAR working well under very bad environment.
Objectively speaking, I think highly of this tiny guy against bad environment.
And here is the comment of the client who took the picture.
TFmini matches drone very well in
Read more…Hello! I’m having trouble with building the firmware for Skyviper 2450
So, I simply followed the instructions in this site (http://ardupilot.org/dev/docs/skyviper.html2), however I cant seem to build it.
I cloned the codes first using (Ubuntu)
git clone
Read more…Good day all
I have started building my pixhawk drone and purchased the pixhawk, receiver, ESCs and GPS today.
Connected switch, buzzer and GPS to pixhawk. Did the flashing of the software. Completed the calibration of the accs and the mags. Get to the
Read more…hello guys,
Is it possible to attach two batteries of different mah, volt or C rating parallely???
Is possible to attach(parallely) two batteries of
-different C rating same mah and volt?
-different mah same C rating and volt?
-different volt same mah a
Read more…Good day all
Busy building my second drone. Wanting to use a pixhawk with APM software. And since I am new, I have been reading up about this before I go out and buy stuff. One thing that I want to ask - maybe
I just missed it in the docs - ....
Once I
Read more…Good day All
I only have a few months of experience in the RC world. I have completed my first drone : 211-frame. 2206-2500kv motors. Betaflight F4 FC. I added a GPS and BARO and also FPV using the built-in OSD on the FC. Oh... 5040-props.
Next I would
Read more…