Hi all,
I am attempting to create a multi-vehicle flight using Ardupilots built in swarm feature. I am trying to get this done on a tight schedule and on a budget.
I am trying to get this done (for now) on the SkyViper V2450GPS frame since it has ar
Read more…So ive ben trying to do this for a few months now and keep getting no where and setting it back off aside.
Need to get this bird in the air...
Been using this page to setup the parameters. http://ardupilot.org/copter/docs/landing-gear.html
So ive set my
Read more…Hello,
I am creating an autonomous boat and I need some help for arduino programming.
I have a Pixhawk autopilot and I want to read the PWM output of the throttle to control two motors.
I use PulseIn command and I think it's not working so bad... If you
Read more…Hi all,
At Iridium Dynamics we've been working on a long-endurance fixed-wing / rotary-wing hybrid aircraft called Halo. Long story short: we found there is very little choice of high energy-density batteries available for long endurance electric plan
Read more…I have these motors on my quad:
with DJI 9443 props.
My quad has to sit on 70% throttle to stay in the air and when the bat
Read more…Hey guys, first of all, thanks for accepting me as a new member.
I build my first drone by dissesamble other drones and buying new parts.
however the drone is controlled by naze32.
last year i flew it around whole summer. i then before winter, i disse
Read more…Space is tight in my RC plane so I had to place my Pixhawk flight controller on its left side. I was able to orient my Ublox GPS + compass conventionally, meaning horizontally with the arrow pointing forward.
I believe that the board orientation must
Read more…Starting a new Cortex build, then flight testing before being made available for sale.
Ready to Fly CarbonCore’s are on the website
http://shop.carboncore.co.uk/Shop/Ready-to-Fly
And there’s a lot more photos on the facebook page
https://www.facebook.
I'm about to install a pixracer in my Convergence (unless it's an issue). I've been searching but I really am not sure where to look for setup info or to ask questions. I think I want to run Arduplane. I also have a couple of pixhawks not being used.
Read more…Hi All,
Can anyone tell me if the uAvionix transceivers work with the PX4 flight stack please? They are a little expensive to purchase just to try out!
Also, has anyone used them with Mavros?
Many thanks,
Mike
Read more…Can anyone tell me how to get my drone to draw power evenly across my 6s battery.
Read more…Hello guys,
I've reviewed a few drones this year, but the FUUTON 2 is on a whole different level. I'm not really sure how you can even get better than this for this price.
I've reviewed it over here https://www.youtube.com/watch?v=UpJdHfC-hbA
What do yo
Read more…Hi,
I have ordered an uBlox neo m8t module at Drotek. It arrived yesterday in the condition depicted below (the right one). I think that is not acceptable since the other module (the left one) has not the same scratches, marks and is not dirty as this
Read more…Can anyone point me to shematics for APM 2.6, 2.7 and 2.8? I am looking to redesign to a micro form factor in order to make micro drone UAV's. My goal is to create micro drone swarms suitable for indoor terrain mapping.
Read more…Hola a Todos, recientemente inicié mi proyecto de AT, seguí las instrucciones básicas de Ardupilot para AT en el MP, pero no logro con éxito que funcione como debería hacerlo correcto. Alguien que me apoye a encontrar mi error.
Read more…I built a largish fixed-wing UAV (Hugin 2.6m, roughly 8 kg MTOW if I recall). It's definitely too large to hand launch, and it needs a surprisingly long takeoff run (especially on grass) to get airborne and clear of trees etc. This is fine when I h
Read more…I did not attempt to fly one yet. But, I am dying to do one! Do I need any special training before I can fly a drone? I asked LeveTop guys, they said I don't need any particular special skill, they will send a manual with their product so that I can
Read more…Hello,
I have been using UgCS for one of my Hobby projects where I plan to use 2 Arducopters. I plan to run completely autonomous mission, so I was trying to use a single RC Link/Radio and switch between models on the radio to establish manual links
I have a virtually unused (6 flights total) factory built Y6 complete setup for sale. Purchased in early 2014.
Includes Copter, Spektrum 6 radio, 4 batteries, chargers, FPV screen mounted to radio, extra arms/legs etc. purchased with copter.
Copter was
Read more…So I just maidened a new build this weekend and have a few messages in the log that I just want to run past the community.
I know this is saying I have an EKF issue and then it clears, but I cant’ find what the cause is.
Err EKF_Check-2
Err:EKF_Check-0
T
Read more…