Hi all.. I have been trying out the new program and i found a few questions to ask.
Hello I am new in this hooby.Plz told me how can i make an omnithopter UAV.
Read more…I would like to know do I need any component to control a DC brushed motor because I currently have a ESC, DC brushed motor, APM.
Thanks .
Read more…Is there any way to check the functionality of a shield board without having it connected to a pilot board?
I manged to short something on one of these two tonight and I now can't get any lights on either board unless there is a FTDI cable connected.
hi all again :)
i am getting a lot of servo jitter on my middle switch. i have them setup as
#define POSITION_1 MANUAL
#define POSITION_2 STABILIZE
#define POSITION_3 FLY_BY_WIRE_A
manual is fine, rock solid
i get a lot of constant jitter and twitch on s
I would like to receive telemetry data (or really, any data) and pass it to another microcontroller inside of my plane. Would this be feasible with the current I/O and software setup of the ArduPilot Mega?
Read more…Hi all,
this is my first post on this forum: I just registered after having seen some cool videos around.
I'm a web developer by day, the maintainer of a pretty popular (at least in the .NET world) opensource project. But lately I'm starting to play ar
Hi,
I've been reading a lot on different forum and probably got bitten by the Arducopter ;-)
I'm planning to do this step by step. I just ordered the APM and oilpan.
Looking in to software I stumbled across this http://code.google.com/p/arducopter/wi
Read more…Ive created a program that emulates a MTK gps from coords received from Xplanes.
So you connect a FTDI cable to the gps com port on the mega, and the program sends MTK binary messages to your APM. Its included in the latest ArudpilotMegaPlanner 0.4.6
Read more…
I have an EasyStar with ArduPilot and ArduIMU. I've tried multiple configurations of the hardware in the EasyStar and cannot find a suitable location for everything. How does everybody have their equipment setup in the EasyStar including the batter
Read more…Hello All,
Ok so I’m new here and I have been researching through the forums and other sources the past few days for a project I am involved in. I have already learned quite a bit. I still have some questions and I will do my best to phrase them
Read more…I have an experimental aircraft that I have flown for many years. I know that the autopilots discussed here are for model aircraft but.... The idea is to have the auto pilot drive small trim tabs on alerons to gently level the wings in flight. It wou
Read more…Hi all,
I'm trying to recieve the NMEA 0183 from Garmin GPS 18LVC.
However, the Ardupilot software program is only support for Locosys type GPS.
So I remove the Locosys setting and put Garmin GPS configuration sentences.
Unfortunately, Ardupilot still
Read more…Hello I have been trying to solve GPS locking problem for 3 days.Could somebody help me how to figure out??
The problem is blue Led is always blinking.Even in the midde of grassy plain.(and also sky is clear) and it's blinking gps module not connect
Lately I got into talk with several people at the airfield, both glider pilots, fullsize glider pilots, beginners and advanced pilots.It was just one off all these people that had taken the step to buy an autopilot set(Papparazzi), the other ones wer
Read more…Hello All,
I am getting started on developing an IMU for the paparazzi system. Anyone that would like to throw in their comments and ideas would be appreciated. In the end I can read the tech docs and come up with a lot of the values myself but I might need an
Read more…Just before sunset, new ixus 100s camera, ardupilot + other stuff, sh*t, f*ck and so on.
Goldberg Electra + tsunami 10/15 + Rhino/Zippy 3700mAh Lipo (!)
Maybe too windy, it takes fine 1st turnpoint upwind, but next downwind TP, i think last and then la
Read more…I am working on a motion tracking project using an ArduIMU+ V2 and am wondering what the unit of measurement is for the Accelerometer output.
Read more…Hi ,
I am Doing project on location tracking using inertial sensor, I have ADXL335 board. I am not good in programming. I have a task to make a programme to transfer the data from the board to the terminal device (siemens TC 65). In short , I have to
