I'm getting this compile error from the latest code in the repository?
In function 'void print_current_waypoint()':
error: redefinition of 'void print_current_waypoint()' In function 'void print_control_mode()':
In function 'void print_position()':
In
Hi dear specialists,
I got my easystar flying well with the 2.5.4 Version. Thermopiles
Now I added telemetry X-Bee 2,4 MGHz and ground station beta 2. Generally it works fine, but:
The Elevation shows always around 13000 meters.
Google Earth shows the sa
Hello All:
I need an urgent help on the firmware uploading for ArduIMU ver2. The main problem is when I upload the firmware, Arduino shows "Uploading to the board", and nothing apprears then. And the arduIMU now is with RED & YELLOW LED consta
Read more…Hello i'm new to Diy Drones but i have been following posts here for a few months now. I have finally bought nearly all i need to complete my first Drone altho i have gotten stuck. My problem is that the plane i have is a 4 channel plane and im not s
Read more…I'm just wondering if anyone has tried this. I have talked to some people that said this could give me a range of well over 1km, and plenty of bandwidth for data up/down and video downlink.
Anyone see a problem with doing this (I plan on using a netb
I was perusing online stores yesterday, when I found several flat panel 2.4ghz antennas in the 15 dollar price range. Coulld one of these be used on a Tx to extend range? I mean, they have the nice ones, with a very tight beam, but then Ii'd have t
Read more…I've been following the IMU discussions with much interest.
The DCM imu work is very interesting, but it is fairly specific
to aircraft. Even then the GPS assumptions as applied to aircraft have significant faults,
Small UAV's will easily fly as speeds
Would the ardupilot boards be capable of controlling an aeroquad design?
Read more…On this page......... http://code.google.com/p/ardupilot/wiki/SolderingBoard it says I can solder a wire from the arduPilot shield to the positive terminal of my battery connection to send the batteries life back to the ardugroundstation. Bu
Read more…I have a hawk sky for my UAV platform, but the motor mount and the opening for the power and ground cables to go down through the plane to the ESC is so small that when I connect the motor, I can't get all the wires down into the planes fuselage. Is
Read more…Hello All,
I need to turn my servo gains down, as I'm driving a little drunk, but other than that.....
Altitude hold is excellent.
WP navigation is excellent in my bo
Hi
could not enter programming mode.
I already tri
I have flight gear installed, I have the ArduFlight_247 code running on the arduPilot and I am using a arduIMU. I have made a mission with the Config tool download and I have downloaded the arduFGcontrol1.1 file..... But can someone give me a step by
Read more…It seems that the ArduPilot guys are doing a great job and are really starting to push new development, but I'm having an issue with it all. If I want to get everything going right now, it seems very easy enough to buy the ArduPilot, the plane, and
Read more…I have this setup running. I have arduPilot with blue arduPilot shield along with ublox gps and arduIMU. In fly by wire and stabilization mode without the blue arduPilot shield, these two modes work perfectly. However, when I put the shield on the a
Read more…I've developed a sudden interest in quadcopters, and have been doing some reading. However, there are a few questions I haven't found answers for, so I'd like to draw on the expertise-at-large here.
Hi, I'm completely new to the drone/autopilot community, but I'm using (or attempting to use) an ardu-imu in a school project. My goal is to use the IMU's sensor data to actuate a servo-operated camera gimbal system to keep a camera facing orthogonal
Read more…i want to do a project on anteena tracking based on maximum recieved signal strength so if any body provide me the circuit as well as the software because i am much confused about how to move anteena automatically with the moving object please help
Read more…Hello All,
Has anyone had any luck measuring fuel flow or fuel volume in a glow fuel powered aircraft?
I was contemplating using a differential pressure sensor to calculate the mass flow rate between the tank and the needle valve, but I have a hunch that the ove
