I'm getting back to my APM 2.5 after a long break with other hobbies.
I have a Traxxas Summit with the APM mounted on an ABS platform, using the Power module (jumper removed.)
I'm using a Futaba T9CHP radio with Dragonlink V2, APM 2.5 w/ LEA6 external
Read more…Hello everyone,
Our team has been working a few days trying to get the steering correct on a Pixhawk controller and we have been confused about the heading data the ArduRover v2.49 uses.
We have a RTK receiver that will give a very accurate true headin
Read more…Hi folks,
I was doing some testing before the AVC next weekend and everything was running pretty well. While connected, all of a sudden I couldn't get GPS lock anymore and when I looked, none of the APM lights were on (while connected to USB). I've tr
Read more…Howdy All,
I stumbled across this project yesterday. It uses UWB Decawave chips. The Pozyx is a Arduino shield. The system is made up of 4 anchors around the room and 1 arduino compatible tag. A Pozyx team member confirmed that their system could be p
Read more…I took my bot out of storage after a few months (too busy for fun !). Updated MP to 1.3.24 and took it outside. Link is fine and I get 13 sats and everything seems good but the location of the bot on th MP flight data screen is off by at least 200 f
Read more…I use the APMRover with Pixhawk ,GPS and a skid steering rover .It's perform very well in Manual Mode.But when I switch to Auto Mode it switch to RTL Mode automaticlly.It still can switch to Manual Mode ,Hold and Learning Mode at any time.Neither RC
Read more…I dont know but seems my left sensor is not working at all....Please Advice
Read more…
I want to use pixhawk with the apm rover firmware to operate an agricultural tractor. I need to set up my tractor as an rc vehicle. My plan is as follows: any feedback I can get is appreciated. I plan to order the parts in the next couple days but
Read more…I successfully got my rover to follow me around the yard. Right now the code tells the rover to come when you push the down arrow button. I plan to experiment with having it send a new location every x seconds and also be able to add some offset. I
Read more…i am newbie to ardurover, and want to build an ardurover from scratch with brush motor. does the APM 2.6 can directly control brush ESC, if not, what is the modification should i made to apm.
Regards!
I am planning to try the dual sonar option on the latest ardurover version. I am following the instructions on this forum. Does the dual sonar work ? My max vehicle speed is 2.1 m/s so I think it should be fine. Comments ?
Also, is there anyone using
Read more…hello,
I have an Arducopter and an Arduplane and would like to build an Ardurover using an existing APM 2.6.
What is the largest frame for an Ardurover i can buy ?
Does ardurover support 4 wheel drive ?
I want something i can send back very rough ground
Read more…Hi,
I upgraded MP yesterday and there are no apparent problems - thankyou for a good release.
I'm using 3DR PIxhawk with 3DR telemetry.
At the top of the Flight Data Screen I have a new red symbol (top left) and a yellow slider next to it.
The attached s
Read more…Hello DIYDRONES,
I am a senior in mechanical, and aerospace engineering. For our senior design, my team has designed a pylon racer that air drops a 1/16 scale car. We get a score bonus if our team uses autonomous for the ground mission. I currently ha
Read more…Hi and thanks in advance to anyone who can assist.
Kit will be going into a RC boat but will use Ardurover and is currently mounted on a plank.
Kit is 3DR PixHAwk, 3DR Ublox GPS, 3DR radio, Spektrum satellite Rx, mission planner 1.3.21 Ardurover 2.49.
I
Read more…I need to use channels 7 and 8 on my "Immersion R/C 8 channel" receiver to control two switches. Is it possible to change the default ch 7 and 8 functions on my pixhawk (Ardurover 2.91) to use ch 9 and 10 respectively?
As of now I have PPM (Immersion
Read more…I cannot get the APM to read the battery voltage.
APM2.5
Ardurover 2.49
Voltage tapped off of 2S battery with potentiometer (8.2volts in=3.0volts out)
Monitor type is set to voltage only
Sensor (none),
I have tried changing the monitor point from A13, A0,
Read more…Hi,
I posted the following on the Tower (DroidPlanner) Git issue forum, and received a reply that this may be an ArduRover issue, rather than an OCU software issue. Interestingly, when I use MissionPlanner I don't seem to have the same problems - but
Read more…Hello.
I set myself a challenge of hooking up APMRover2 to a car simulated in MORSE and it seems to work so I thought I'd write about it. Might be interesting to someone.
MORSE is a robot simulator based on Blender's Game Engine. MORSE is different to
Read more…
tiny video switch
Can ardurover trigger a camera switch based on accelerometer position?
Read more…