Gender
Male
About
Location
New Orleans, LA
Please tell us a bit about your UAV interest
I am interested in aerial photography for mapping purposes.
Hometown:
New Orleans
Activity Feed
Are there any ways to create remote desktop connection or ad-hoc connection from a ground computer to a computer (windows or linux based) attached to a UAV? I need to control an pc based application that will be installed on the computer attached to…
"I've been using the following combinations:
1. Taranis and the DJI 2.4 Data link for over a year once a week and have had no issues.
2. Graupner MC-32 and DJI 2.4 Data link for over two years now and have had no issues.
Hope this helps"
1. Taranis and the DJI 2.4 Data link for over a year once a week and have had no issues.
2. Graupner MC-32 and DJI 2.4 Data link for over two years now and have had no issues.
Hope this helps"
"Alexey,
I'm using a Riegl RiCOPTER with a VUX-SYS (LiDAR and 2 x Sony A6000 cameras). I have a very similar calibration/ workflow as Eben's Phoenix System. The added "Area Scan" tool has been a big improvement for us in large area mapping…"
I'm using a Riegl RiCOPTER with a VUX-SYS (LiDAR and 2 x Sony A6000 cameras). I have a very similar calibration/ workflow as Eben's Phoenix System. The added "Area Scan" tool has been a big improvement for us in large area mapping…"
"I too, run LiDAR and would be very interested in a template feature. "
"Yes!...Loiter for a boat. I've been waiting for this for a long time. A Big thank you to the devs!"
"Im using UGCS with the Riegl RiCOPTER and the previous version allowed me to specify what to do when the battery was low, loss of GPS, loss of RF in each mission. Those options are now gone. Is there a way to select those options or is there a way…"
"If you search the internet...you'll find hundreds of designs for foamboard planes. The flighttest versa blunt is big enough for your looking for. I found this guy's designs several years ago - FPVTrond check out his youtube channel…"
"I fly one of these for work, without the turbine of course. Its a Riegl RiCOPTER and it is made to carry a Lidar sustem. Just scale those are 30" props."
"I tried all those things and cleaned out the registry, but still get the same errors.
Thank you,"
Thank you,"
"Yes I did and it connected but it would fail to load my routes. I posted here: http://diydrones.com/group/ugcs/forum/topics/route-untitled-route-u... and I was told that UgCS 2.7 would not work with ArduCopter 3.2.1.
Thank you for the quick response."
Thank you for the quick response."
I am trying to test and become familiar with UGCS before buying it, but I'm running into a few issues. I tried to install the most current version of UGCS 2.7, but this version does not work with ArduCOPTER 3.2.1 (arduCopter 3.2.1 is the most…
"Thank you. Like I mentioned my company has a Reigl RiCOPTER and we are going to be using UGCS for its mission planning and flights. I wanted to get fimiliar with UGCS's functionality first on a smaller rig."
I am having issues getting my 3DR Y6 APM 2.6 to accept my missions/ routes. I can connect and get telemetry from the copter, but I cant upload missions. I get the following message:"Route "Untitled route" upload failed. Route not accepted."I…
"Very nice! Thanks for sharing. I've built several ardupilot planes, copters and one rover over the years. I'm thinking of building a boat next. Would you mind sharing the steering servo you used? I'm unsure of the torque needed to handle the thrust…"
"@stanley anak suab did you calibrate your ESC? (remove prop, full throttle, plug in battery, throttle back down....you should here a tune)"
"the current version uses 29" props"
