I just purchased a used Iris+ with gimbal and GoPro3 and FPV. I have downloaded the Tower software to my Samsung Galaxie S5 phone. I have not been able to get the Iris to connect to my phone with the WIFI. I cannot find the wifi signal from the Iris.
Read more…I heard that that 3DR is phasing out our IRIS+ to focus on the SOLO.
Is this true? Love my IRIS but Is it time to sell it?
Read more…Appreciate some help identyfying this snag
The original 3DR controller stopped working and I have replaced it with a Taranis Plus.
Using Iris with this setup Fr Sky D4R-II RX / Taranis Fr Sky DJT TX:
When connected via Mavlink, Mission Planner shows t
Read more…Hi Alls.
I'm sorry to put up one question by another. After I update my firm ware because of the control show all 0 value. Then the problem start. When i start to dis arm is show PreArm: Need 3D Fix.I don't know what is that and where to look for. I h
Read more…My Iris+ show no voltage at the control. All lights are up and other figures had shown.The battery is full charged but the screen show 00 vlt. I change other 2 batteries show same. What I have to look for. Also frequently have to re calibrate the rad
Read more…Hey gang. I pulled out my daughter's loose tooth with my 3DR Iris, and it's going to be featured on The Doctors show on national TV today
https://www.youtube.com/watch?v=6uyUmnr0JIE
Read more…
i been working a lot and finally had time to fly the IRIS+ , great lil copter.
but i am having a minor issue of how to change the orientation of how it flies.
it appears that it sticks with how i am positioned in flying..
yaw works ok,, forward and back
Read more…My previous discussion was channel 1 no signal. My remote show not data.So I try to open the top cover of Iris+ to see anything that came loose. After I open the cover I saw one harness from the receiver was not plug in. I don't know is accidentally
Read more…My Iris+ won't start and I look at the control the dot is way off from right bottom for disarm. So I try to calibrate and it show the error message of "Channel 1 no signal. I've 0 experience for the system. Just know to fly only. But I can take apar
Read more…I lost my 3dr ground station from iris+. So, should i buy new 3dr ground station along and connect it to air station? or i need to buy both air and ground stations and change it in the iris+ guts?
Need a good answer because i'm a new in such questions
Read more…I took the guts out of a old Iris+ and put most of the parts on a 470mm frame. I have a Q-Brain 4 in 1 25A ESC going to cheerwing 920KV motors. During standard calibration the motors twitch and one of the motors smoked a tiny bit. This is with a 5200
Hi I have got a ilook+ camera for my iris+ and can you tell me how I can take photos useing my transmitter radio can it be done I posted this the other day but no replies at all
Read more…Hi just got a camera ilook+ takes great videos but how can I take photos with iris+
Read more…Hi, Any help please, I have a Iris mapping using a camera canon s110, I can trigger the cam in mission planner, my problem is when ARM the iris the camera shot pics without any order or command, shot continous and not stop, every 10 seconds any help
Read more…I'm still trying to find an answer to this after a couple of weeks of being down, 3DR support has been pretty slow on the uptake.
Basically, my Iris+ isn't getting commands from my radio controller, i.e. the box with the joysticks and the FrSky DJT. M
Read more…I recently tried installing the 3DR Bluetooth Data Link on my IRIS+ via the TELEM2 port. I was unsuccessful in getting MAVLink messages back via Bluetooth and went to switch that back to the FrSKY module. Upon removing the Bluetooth module the DF13 p
Read more…After changing the flight path on my Iris ( not Iris+) one motor does not spin, it just jiggle. It seems like the ESC is trying to hold the motor in place. It is harder to turn the motor by hand when it has power than when it is off. I did the ESC ca
Read more…I've been flying an IRIS+ for about a month. I recently noticed that the "expended" current of the IRIS+ is no longer showing up on the transmitter; only 0. I usually monitor the current to make sure I don't exceed 4080 mah on a battery. Any ideas ab
Read more…hi everyone I have got a iris+ now I got a gps mast and I need the cover that goes on top of the3DR uBlox GPS,i emailed 3DRobotics Inc and they said they only do cover for gps when you buy the complete gps I don't want to spend £60 just so I can get
Read more…