I know that I2C splitter can accept digital sensors like Airspeed ,, Compass , GPS , Leds , USB
I need to add RPM Sensor to pixhawk , Can I use I2C for that ?
Dose the I2C accept any digital Data ? OR just special Sensors ?
My problem is that I need to
Read more…Hi all ,
I see that the Arduplane and Pixhawk support the Parachute setting ,
I have Plane similar to skywallker and I need to setup Parachute . but I don't know where to start .
Can you help in where I can find suitable Parachute for my plane with weig
Read more…Hi all ,
I need to hack Camera go pro to control throw pixhawk
I remove the power switch cover of the camera and connect it with two wires ( when connect them together ) for 3 second the camera ON when do it again the camera of .
Now Can I connect them
Read more…Hi all ,
Can I pass the GPS information maybe( NMEA ) to Google earth software in real time and flow the path in google map ?
maybe in the temp window of mission planner ( Ctrl+F) there are some thing about GPS like
GPS inject ?
MAV Serial Pass ?
for what
Hi all ,
I am using telemetry 9xtend900 mhz to send and receive pixhawk data , and I am using Video throw video transmitter .
now I have information to send such as :
Sensor data
Camera control data
Gimbal control
that data doesn't work with Pixhawk So I n
Read more…Hello all ,
I have G-3D Gimbal controller from walkera and I want to attach it with pixhawk ( actually its chines pixhawk called pixhack ) but it's similar to pixhawk .
I tried to connect the wires from the gimbal to pixhawk put when I power the gimba
Read more…Hi all ,,
I am using Arduplane with my gas plane ,
I want to include some sensor such as
RPM sensor .
Fuel level sensor.
Motor Temp Sensor.
I need to add them to pixhawk and control them from mission planner .
Is there any information about this ?
How to ?
Be
Read more…Hi All ,
I have tested my plane with one Airspeed sensor MPXV7002DP Also wrote on it "CY" and "K1419"
and It works fine in Auto mode and every thing is ok .
-----------------
know I use another Airspeed MPXV7002DP
but wrote on it "CV" and "K1419" the thir
Read more…Hello all ,
I just get Digi 9xTend 900 Mhz and I want to connect it to my pixhack ( chines pixhawk )
I can't configure the 9xTend and connect it to the XCTU software using TTL ,
the pin out of the 9xTend is :
pin 1= GND
pin 2 = VCC
pin 3 = GP02/RX LED
pin 4
Read more…hi all
I am still in the ground and I have many error messages in HUD screen in mission planner ,
such as :
- "Bad AHRS" even after I did all calibration ,
- "Bad Compass Health " I did calibration .
- " Error Compass Variation "
- position errors
when I p
Read more…Hi all ,
I am happy that my plane start to work in auto mode , but still facing some problems .
I tested my plane with auto mode and it seem to works good , with control altitude and throttle while using airspeed ,
I set 5 waypoint with 100m distance f
Read more…Hi all ,
come back again with Question that I think It will solve my problem ,
I connect My pixhack system with GPS as RC receiver and connect it to Mission planner ,
ArduPlane V3.4.0 (3aa9eb0c)
PX4: c4f39028 NuttX: d48fa307
PX4v2 002E0034 31345102 3135
Hi all ,
I am try to use flightgear simulation with MP to simulate my flight ,
maybe this way will allow me to solve problems I faced.
Compenents :
Mission planner v.1.3.32
Flightgear v.2.10.0.3
Pix FMU+IO (china pixhawk ) also ( APM 2.5 )
I followed by th
Read more…Hi again ,
I am still having problem in Auto modes using Pixhack FC
My Question is
What's the different between ( Absolute , Relative , Terrain ) Altitude in Mission planner ?
Whats is the function of the check box ( verify Height ) ?
also in the right si
Read more…Hi All ,
Hardware:
- Flight controller : PIXHACK
- GPS Ublox
- MiniOSD
Software:
- GCS : Mission Planner.
- Firmware : Arduplane 3.4
Problem:
After previous tests and posted topics here I solve the problem of pitch
Read more…Hi all , Come back again after test,
Hardware :
My Own plane , similar to Skywallker ,
Flight controller : Pixhack CUAV .
GPS : Ublux 7
other additional tools ,
Software :
Firmware : Arduplane 3.4
GCS : Mission Planner.
with out AirSpeed , throttle cruise 60
Read more…Hi all ,New Questions in this discussion will provide me with good knowledge . Hope find interest answers .actually I use Manual and Stab modes It works well for me , Need to try other modesFirst : How to use more than 3 mode in the flight ?and How t
Read more…hello all
I Hop to find real useful information and solutions .
Hardware:
-SkyWallker
- APM 2.6 ( also test with Pixhack )
- GPS ublox
- MiniOSD
-
Software:
- Mission planner 1.3.32
- Arduplane Firmware 3.4
I test the Auto mode in the flight but when I c
Read more…Hi All ,
I had many crashes with my plane
I am using Arduplane 2.6 and pixhack (Not pixhawk ) and both has the same problem .
When I change mode from stab to Auto the throttle is off and plane start loss altitude while heading to waypoing direction.
I d
Read more…
Hi all ,
I have problem in controlling my plane with the elevator and aileron
when I move to max aileron stick the plane pank with big angle as will as with elevator.
this make the flying hard
I want to know how to Limit the movement Angle for the stic
