Gender
Male
About
Location
Flores
Please tell us a bit about your UAV interest
All drones!
Hometown:
Trinidad
Activity Feed
"I live in a country right next to you Cala and the same problem here. The solution for this problem: buy a ticket to the USA and pick it up yourself (some other things to resale when you come back helps lowering the costs :-)"
"I agree that C rating is really overated, I use Multistar 6S 10000Mah x 2 in my big copter and so far they are working great. however I have at least 25min flying time so I try not to use it beyond 2C to 3C. I also balance them everytime I go out…"
"Two things: Has anyone read this from the release notes?:
4.12 Navigation rate The recommended maximum navigation rate supported is 5Hz for standard multi-GNSS operation (GPS + SBAS + GLONASS + QZSS) and 10Hz for single GNSS operation, when Galileo…"
4.12 Navigation rate The recommended maximum navigation rate supported is 5Hz for standard multi-GNSS operation (GPS + SBAS + GLONASS + QZSS) and 10Hz for single GNSS operation, when Galileo…"
"Hi All. I am receiving a couple of M8Ns these days (a CUAV M8n with 5983 and a much cheaper M8N from Bangood) and I am planning to update the firmware. I will try to test it with the stock one and the new one just in case and I´ll post the results…"
"When I first saw this post I thought "Well yet another good product but for ten times the cost of the standard one" but my curiosity led me to look at your store. I could not believe it was only U$S 33 for the 200A version and free shipping!
Let´s…"
Let´s…"
"I think Robert once said that it was working. Maybe is not so difficult to implement. I would also be saffer than using a Y cable"
"Hi Randy. I installed 3.3.1 RC1 today to test and issue which I have with no SBUS output on a Pixhawk controller. I´m trying to connect a Storm32 controller. If I make a direct connection between the X8R and the ST32 I get no problem, but I i try to…"
"Hi, has anyone been able to make the SBUS output work? Thanks"
"Hi Randy. Can you check my post regarding SBUS output. I have been trying to make it work but so far no good. Thanks"
"Hi Randy! I have been trying to get the sbus output to work today but I had no luck. I have a X8R and when I conect my Storm32 controller directly to the receiver I have no problems but when I try to do the same on the Pix I get no response. I have…"
"Hi. I have asked for the same thing too. It is useful for those of us who use a double power system to take off as soon as the battery is replaced.
I think it will be done for 3.4"
I think it will be done for 3.4"
"Exactly. Another use is taking off from a boat. I need to start the apm on the shore to make the gyro cal and them move it."
"Hi. This is a question for the developers but I´m not sure it is a 3.3 only thing.
I have a big octa which has an extra battery for the gimbal and the pixhawk conected to an output so when I deplete the main one after flying, I can put a new one and…"
I have a big octa which has an extra battery for the gimbal and the pixhawk conected to an output so when I deplete the main one after flying, I can put a new one and…"
"Hi Randy. Something related to this? In MP you can see the MagField for the compass being used by the FC. But what about the other one? Is there a way to read it? Maybe APM PLanner or Tower can show them?"
"This is great info! I did not thought about the second autotune right after the first one but is a logical thing.
I know the default PIDs are really conservative (or maybe they are thought for small overpowered copters) but I have a large octa and…"
I know the default PIDs are really conservative (or maybe they are thought for small overpowered copters) but I have a large octa and…"
