Gender
Male
About
Location
Philadelphia, PA
Please tell us a bit about your UAV interest
3DR Y6 Owner
Hometown:
Philly
Activity Feed
"Excellent find. Exposing a vulnerability like this will bring about competition and change for a more secure and robust telemetry network for drones. As a user, I'm glad to hear that there are already some options from the comments above. "
"Just here to confirm that the link is dead. "
"I see the Sony NEX-3N listed.. Can I assume it'll work with the rest of the Nex series? NEX-5 and 7?"
"This is a complex issue, but the drone pilots are certainly at fault in this situation. I don't see any issue with allowing the firefighters to eliminate/down drones that are violating emergency airspace. Dump water on them, trash them, whatever…"
"I'm very curious about your software stabilized video. Are you using a lens and sensor similar to the Parrot? "
"I'm very excited to know more about that transmitter! Interesting timing on the news too, just before DJI's April 8th reveal. "
"This is simple and effective. Thanks for the good work!
Here is another resource that might inspire you for content. Previously this has been my go-to when checking weather before I fly:
http://www.usairnet.com/cgi-bin/launch/code.cgi"
Here is another resource that might inspire you for content. Previously this has been my go-to when checking weather before I fly:
http://www.usairnet.com/cgi-bin/launch/code.cgi"
"Which version of the CrazyFlie is it? 1? 2?"
"The maximum horizontal speed of the copter during loiter mode can be adjusted with the Loiter Speed (aka WPNAV_LOIT_SPEED) parameter on the Config/Tuning >> APM:Copter Pids screen. The value is expressed in cm/s so 500 = 5m/s. The maximum…"
"This worked for me.
Issue: no updates just all static numbers on the OSD.
Fix: Bad Y-Cable from GoodLuckBuy.com - it has one fine pitch connector APM, then a 0.1" connector for telemetry (which worked), then a 3 pin 0.1" connector for the OSD.
Cut…"
Issue: no updates just all static numbers on the OSD.
Fix: Bad Y-Cable from GoodLuckBuy.com - it has one fine pitch connector APM, then a 0.1" connector for telemetry (which worked), then a 3 pin 0.1" connector for the OSD.
Cut…"
"Do the WP_NAV parameters affect the follow me mode at all? (Other than WPNAV_LOIT_SPEED)
EX: WPNAV_ACCEL, WPNAV_ACCEL_Z, WPNAV_LOIT_JERK, WPNAV_SPEED_UP, WPNAV_SPEED_DN
Whats the fastest object/person/vehicle that has been tested with Follow Me…"
EX: WPNAV_ACCEL, WPNAV_ACCEL_Z, WPNAV_LOIT_JERK, WPNAV_SPEED_UP, WPNAV_SPEED_DN
Whats the fastest object/person/vehicle that has been tested with Follow Me…"
"@Brandon - Thanks. I'll give it a try later today, I think I really need to get a tablet. Do you know if this Tablet would be good enough? - DX.com Freelander 7"
@dr0n3droid - Wouldn't it depend on your fail-safe settings? I configured mine to RTL…"
@dr0n3droid - Wouldn't it depend on your fail-safe settings? I configured mine to RTL…"
"I gave it a quick test flight with my Y6 and it worked better than I expected for a short test! What took me a minute was to determine that the RC control needed to be in Guided mode for Follow Me on Droidplanner to work.
The only thing I'm curious…"
The only thing I'm curious…"
