Gender
Male
About
Please tell us a bit about your UAV interest
I love quads
Hometown:
Miami
Activity Feed
Hi,I attached log file URL (18mb), if someone could review and let me know if anything is off or wrong.Towards ending of flight, I had no throttle. it went to 0% and no matter what range I gave it. Nothing.It's possible I had no RC controls and not…
"Could i possibly use 2 of the 1w zener until i can source a single 5w zener?
Can they work like that?"
Can they work like that?"
"Ok I went to a electrical component store.
I bought some zener diode
It's a 5.6v zener diode. But the person said it was 1W. Will it work? I bought 5 since they cost little or nothing.
The documentation wiki says to use a zener diode 1n5339 , which…"
I bought some zener diode
It's a 5.6v zener diode. But the person said it was 1W. Will it work? I bought 5 since they cost little or nothing.
The documentation wiki says to use a zener diode 1n5339 , which…"
"Which way is the diode installed?"
"Ok, so I just need to make my BEC wire small as possible. I will also set the bec to 5v instead of 6v"
Are the main power port and the servo rail GRNDS connected or are they isolated completely?I'd like to know if I will have a ground loop with the attached layout.Curent sensor powering pixhawk and a UBEC powering servo railANACONDA-WIRE-LAYOUT.jpg
"I'm very interested in this gimbal. For sale?"
"Well, i fixed it by reseating the sd card in the pixhawk.... Why was this even needed to be done?
What would happen if the error happened during flight?"
What would happen if the error happened during flight?"
my pixhawk led indicator is showing solid red on power up and also repeating a tone that ive never heard before.I flew it, landed safely and waited couple mins then put in a new battery and now that happens???
"Ok,
So, before trying to tune the gimbal from stock what came with my iris.
I swapped out LOITER mode to POSHOLD mode. And amazingly that did the trick, it's a lot smoother than LOITER. No more jitters from what I can see, did 2 test flights."
So, before trying to tune the gimbal from stock what came with my iris.
I swapped out LOITER mode to POSHOLD mode. And amazingly that did the trick, it's a lot smoother than LOITER. No more jitters from what I can see, did 2 test flights."
"Hi Marco,
I will post the logs soon as I can. I am away from the quadcopter.
However 'Thorsten' posted a discussion concerning the issue, it looks like the same problem I had.
http://ardupilot.com/forum/viewtopic.php?f=80&t=10230&sid=3..."
I will post the logs soon as I can. I am away from the quadcopter.
However 'Thorsten' posted a discussion concerning the issue, it looks like the same problem I had.
http://ardupilot.com/forum/viewtopic.php?f=80&t=10230&sid=3..."
"I'm using DJI E600 Package.
6S 20A ESCs and 415kv motors."
6S 20A ESCs and 415kv motors."
"I had a small issue yesterday after flying 3.2 RC14 for the first time. I am uncertain if its a firmware issue or what.
I took off in stabilize mode then switched to loiter mode. After hovering in loiter for maybe 5-10secs, the quad jumped in…"
I took off in stabilize mode then switched to loiter mode. After hovering in loiter for maybe 5-10secs, the quad jumped in…"
"My compass calibration seems to be very fast. It normally takes long to complete.
Is the new versions now faster with compass calibration ?"
Is the new versions now faster with compass calibration ?"
"I got it fixed. Had to update MP to latest beta and i saw back POSHOLD"
