Location
La Vergne, TN
About
Please tell us a bit about your UAV interest
Middleton
Hometown:
LA Vergne
Activity Feed
"Greg,
Thanks so much for the response. I'll be posting a photo showing the level of the props, I'm 95 percent sure we are good there however.. I did go over the ESC MIN->MAX values and they were inconstant, each differ by as much a 5 which could be…"
Thanks so much for the response. I'll be posting a photo showing the level of the props, I'm 95 percent sure we are good there however.. I did go over the ESC MIN->MAX values and they were inconstant, each differ by as much a 5 which could be…"
First let me say thank you, I've been a Pixhawk user for several years and think the work of the FC. This is my first HEX build so obviously I put a Pixhawk 2.1 inside.This is the first flight of a new build, one which I had trouble configuring the…
So, my first need to geotag.. Images and I thought all was fine until problems with post processing... then I notice each photo has the same exact GPS Data in its file properties...captured with a cheaper action camera, I set the time within 1…
"I seem to remember the firmware release 2.1.7 changed how telemetry objects were handled by Taranis. After which I just moved to relying on the Ground Station. Phone or tablet.
Sorry that doesn't help much. .."
Sorry that doesn't help much. .."
So, here in TN on Aug 21st me and the crew headed downtown to visit the festival before the Eclipse main event. Afterwards we headed a mile down the road to kill some time at the park (I just happened to bring the quad).We were approached by two…
"Which one, up or down?
(PWM OR ANGLE LIMITS)"
(PWM OR ANGLE LIMITS)"
"Ok, I have finally made some progress in setting up my Feiyutech gimbal where, 'Point camera here' and ROI seems to function as intended however, it would be nice to have the subject (of the ROI) a bit lower in the shot/frame.
Does this mean I…"
Does this mean I…"
"Ok, I have finally made some progress in setting up my Feiyutech gimbal where, 'Point camera here' and ROI seems to function as intended however, it would be nice to have the subject (of the ROI) a bit lower in the shot/frame.
Does this mean I…"
Does this mean I…"
"Mert, replying to your last post..
Sounds like you loaded 3.5.1 APM which includes new features and New prearm safety check Before it will let you ARM the copter. There are two ways to resolve this, one more correct than the other however, if you…"
Sounds like you loaded 3.5.1 APM which includes new features and New prearm safety check Before it will let you ARM the copter. There are two ways to resolve this, one more correct than the other however, if you…"
"My vote is ESC calibration. ..."
"Having similar gimbal issue for a while..
Taranis output channel 6 maps to RC9. For Tilt, I'm using the side nob for this, wondering if that is an issue.
Output channel 7 maps to RC10 for Pan.. ( I did not configure Roll at all)
Problems is , all…"
Taranis output channel 6 maps to RC9. For Tilt, I'm using the side nob for this, wondering if that is an issue.
Output channel 7 maps to RC10 for Pan.. ( I did not configure Roll at all)
Problems is , all…"
"Sounds like your quad is trying to adjust the gimbal to face your ROI point (with success or not) instead od yaw to point the heading as it would before you installed the gimbal.."
"I haven't looked at the link referenced by Bill however, I will say that your approach to backup power is one of hardware not software configuration.
You should be thinking "If my power module/port" fails then ______________
There are a couple…"
You should be thinking "If my power module/port" fails then ______________
There are a couple…"
"I had trouble last year installing two strobes in parallel to my pixhawk. They worked fine (switch by rc channel 9) when the drone was not armed and motors Not engaged however, when they were the strobes were erratic with what looked like trace…"
