Antenna ID Please!
Could someone tell me which of these is most likely to be a 915mhz antenna?
Both came from the same vendor w/ 915mhz radios.
Scott W's Discussions (14)
Sort by
Mission - ROI - copter direction vs gimbal direction
Hi,
I'm trying to plan a flight and am having trouble finding one bit of information.
I remember reading in the past, there is a setting about telling the copter if it should point its nose towards the ROI, or simply rotate the gimbal towards the RO
CG not able to center.. Any Options???
Are there any settings to tell the flight controller it is not at the CG?
I have a small copter, and when using some large batteries, cannot get the CG centered.
It fly's fine, if I can get it off the ground.... Literally, seriously, if I can get t
Auto control in "loiter" stronger than manual control
I've got an issue w/ my small 250 sized copter, that I haven't noticed w/ bigger copters.. I've built a couple small ones now, and they both do this...
when in loiter, if the copter starts to move some direction I don't want it to, (because GPS drift
Manually set ESC end points
I'm having trouble programming an ESC via the automatic stick up/down, etc method.
I found I could manually set the end points in the blheli suite. My values worked great for being connected directly to the receiver. But, they're not quite right w
CG settings, or best practices
I've got a small 250 sized copter, and can't get the CG centered. It's about 10mm to the rear.
It flies fine, and if I take off quickly, everything works properly. If I try to take off slowly, it flips over to the heavy side.
Are there any arduc
CG
I've got a small quad and can't get my CG centered. My flight controller is centered, and can't really go anywhere else.
So, the CG is off. If I take off quickly (almost full throttle for a second) it jumps off the ground fine. If I try to go slo
Attempted fly away, log analysis.. I could use some help.
I was testing rc10 today and took my little 250 size copter basically straight up, yawed around 360 degrees, and back down.. That was the plan. After the yaw, the copter rolled hard left on its own (loiter mode). I attempted to recover, and my rol
Read more…Mission Planner Maps Went Low Res
I've been using mission planner with the default maps it's installed with. They were great, high resolution and recent imagery.
Today I tried a few other maps, and when I went back to google, I no longer get high resolution maps, or it's using a dif
Can't manually override loiter movements.
HI,
I'm working on a small copter, and think I changed a setting I shouldn't have.. Or maybe something else is going on...
I can't overcome loiter drift... I'm hovering in my back yard w/ not great satellite reception, so the copter wants to drift al
250 size quad and ecalc predictions (way off)
Hi,
I built a 250 size quad, and ecalc says I should hover around 6.2A, and in the real world I hover at 12.2.
I've got a 650 size quad w/ 15" props, and it actually does slightly better than the ecalc predictions, so I was hoping the 250 would equa
Crash Log Diag
My copter fell from the sky today. Not sure what happened. I think it's like a guy who posted a crash log a day or so ago, it looks like power failed suddenly.
I don't know how the power plug could have come loose (xt60), but that's my best gues
Sensor Development Stagnation
Hi,
I hope I don't come across then wrong way w/ this question, but I am genuinely curious..
When I was in school in the mid 90's we worked w/ sonar and IR and various sensors doing collision avoidance (on little ground based robots). Then I got jobs
Read more…SR1 settings do not save on Pixhawk
I am trying to change my "sr1" settings in the mission planner setup.
I make a change and upload them. The changes do not take.. If I read the pixhawk config, they are on different values than I set.
I found some old posts where people had this is
