Gender
Male
About
Location
Cypress, TX
About Me:
Satarted back into Rc 6 mo ago after leaving in 1976.
Please tell us a bit about your UAV interest
The new items available to UAV RC
Hometown:
Houston
Activity Feed
"Darren , thanks for your reply. I and using Telem 2 I have not tried to switch to port 1.
I have not run the OSD through the firmware upgrade . Plan on doing that tonight. That may be the missing link.
Been doing a lot of reading about…"
I have not run the OSD through the firmware upgrade . Plan on doing that tonight. That may be the missing link.
Been doing a lot of reading about…"
"Bill thanks for your reply. I have the Video transmitter on a sepreate battery 3s 11.1. Being on the test stand the servos are not active and the battery prowing the PixHawlk are freasly charged. "
Bench testing my PixHawk and trying to get all systems working ...going fine untill I connected up the APM MinimOSD. No Video or OSD. I know the video setup is working because when I pull hte MinimOSD out of the connection I have very good…
" I have received an explanation for the invoice. It seems this is an internal document for shipping support. As an 35 year accountant, I can understand this. I think the invoice should be noted as a shipping document. and remove pricing.
It…"
It…"
"Sorry it was only $27.00 freight. I have always said the warehouse dept is the whole problem with 3d robotics. "
"I just receive an order notification #: R840505568 for an order that I did not place and will not pay for. A $5.00 item and $31.00 freight. this is crazy. What is going on!!!!!!!!!!!!!!!!!!!!!"
"Chris, thank you for your help. I will be need two cables for my two kits. I hope they can expite the cables I would liek to get theis coptor flying this weekend. "
"Chris, thank you for clearing that up. What I have found is that the port on the side is a little smaller than the one on top. I still have the problem of not having the correct cable. I will contact Customer service shortly and I am sure that…"
"The cable on the GPS is a 6 pin port but the port on the APM is a 5 pin. The instructions shipped with the APM 2.6 indicates a 5-6 cable and I received 6-6 cables. I am clearly using the correct port it is marked GPS (hard to miss)."
"My 2 new APM 2.6 were shipped with wrong cable for the GPS. When will the errors end? I can't believe that the warehouse can't get it right. The GPS uses a 5-6 cable (5 pins on one end and 6 pins on the other). I was shipped 6 pin to 6 pin…"
"Neill If you follow the complete blog you see that there were many problems before the windows addition.
Windows 7 has a problem with drivers and sometimes the drivers do not load with the correct configuration.
My problem was dealing with the…"
Windows 7 has a problem with drivers and sometimes the drivers do not load with the correct configuration.
My problem was dealing with the…"
"I bought a new laptop computer with windows 8 and still not able the load the drivers on the TWO 2.6 APM's I have. As you suggested I got and RMA to return the APM. Not sure where to go from here. I would like to get an APM that works. But I do…"
"Chris...
I am still unable to load the drivers and create a com port from MP. I reloaded my operating system on my computer and can see the drivers on the program list but they still do not load. Bill sent me a link to MP but no change.
The 3DR…"
I am still unable to load the drivers and create a com port from MP. I reloaded my operating system on my computer and can see the drivers on the program list but they still do not load. Bill sent me a link to MP but no change.
The 3DR…"
"
Chris
I have loaded the new MPI too no avail. At this point it appears that I have a hardware problem. I am not sure what my options are.
New computer
This computer... refresh the hard drive and reload the operating system.
Cut my hands off…"
Chris
I have loaded the new MPI too no avail. At this point it appears that I have a hardware problem. I am not sure what my options are.
New computer
This computer... refresh the hard drive and reload the operating system.
Cut my hands off…"
"I have tried a different USB cable and tried a different computer. Not sure how to load the drivers other than reloading MP. Is there a installer for t the drivers?"
"Chris any thoughts why my com port is not loading when I plug in the USB port?"
