I have a little project going. I'm planning to create a new circuit bored for the v911 mini helicopter or at least thinking about it. First goal is to make an open source alternative that is as good as the original, but where it's possible to build o
Read more…I haven’t had time to fly for a while so I’ve forgot some of the details about this problem. But I would really like to “debug” my copter today. So what I’m looking for is some advice on how to do it, and what more information I can supply here.
Sona
Read more…I’m looking for a new FPV camera for my arducopter. I bought one of the cheap ones from hobbyking (sony something), which is absolute crape for FPV. A little bit of sunlight and I can’t see any thing L
Could I get some suggestions for a good one, pre
Read more…What happend to this issue has it been fixed yet? I’ve had a lot of trouble with my mag. so I’m hoping I don’t have to replace it.
Read more…
I've had a lot of truble with my copter. But now i've got simple mode working (more or less).
It works fine when I'm flying back and fourth facing the same direction, even for a long time. But if i spin the copter around a couple of times it looses i
Read more…I've just mounted a camera servo, so the camera will move with the quad. But it moves the wrong way. Is there a simple way to reverse this???
Read more…What ever can go wrong always seems to go wrong on my quad. Its not offen flying wheater in norway, but today there is and everyhing is wrong with my quad. I've solved some problems here is what is remaining.
Flying beta 24, standrad arducopter
Probl
Read more…Just got my loiter working :D :D on to misson planning, using APM Planner 1.0.0 i get this error when trying to upload waypoints:
Any idea whats worng?? Im setting home location, that should not be it.
Read more…With the new code beta23 my quad is verry unstable with the gps hold. Its accually better with no hold :) The gps hold worked greate on the RC2 version, and not so good on the ardupirates.
Any tips for fixing this. Its a normal arducopter frame, stan
Read more…Has any one ever tried connecting two 3s lipo batteries in series and charge them like it was one 6cell battery??
This could save some charging time, if it doesn't blow up :)
Read more…Just mounted a sonar on my arducopter. When i use alt_hold mode it is not holding the alt at all. I've enabled sonar in cli and tested it, it all looks good. Any one know whats wrong??
Read more…Hi
Any one know if there exists a module to make the turnigy 9x run a lower frequency??
I'd like to use XBee 2.4ghz but my transmitter is also running this freq :(
Read more…I have a strange problem
I have seperate 5v supply connected to the RX. RX and apm are connected via a gound wire and the signal lines. This works fine when I am at home. But when I am at the location where i fly i cant configure it. Its like APM is
Read more…I use the MTEK gps on my copter. At first it worked fine, but now i need to press the reset button on APM for it to get a lock. I've read that others have had these problems, but no solution.
Im using the NG code. Is there a solution to this??
Read more…I just mountet mag. and gps to my arducopter. But when i try to fly the yaw is unstable :( verry unstable
* Enabled in code #define IsMAG
* enabled in cli
* cal. in cli
It's connected like the pic. Any ideas what might be wrong??
Read more…
My arducopter has fallen out of the sky a couple of times today. I tought it was bad connections, so i replaced them.
But when i started testing again i found that if i move the trottle stick fast it disarms. The arm-led stops blinking and the engine
Read more…I need a new batteri charger for my lipo, current one takes 7.5h to charge :( Any recommandations??
Read more…MY ARUDCOPTER IS FLYING :D :D
But i have spare parts.. Any one know what this is for?
Hi
I'm waiting for my arducopter, in the mean time i would like to see the data it collects. Is there data from the flash posted somewhere? I mean logged flight data
I am trying to calibrate my transmitter, I just bought a new one the turnigy 9x. I do the regular calibration using konfigurator everything looks great. It says it fails cause I don’t use the aux channel. All the markers stay in the center when the s
Read more…