Bert
  • Male
  • Netherlands
Share
  • Blog Posts
  • Discussions (18)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Bert's Friends

  • Antonie Kruger

Bert's Discussions

Connector type ( is it jst sh ?)

Started Feb 29 0 Replies

Hi ,Maybe some one can direct me in the correct way. I have a small connector on a camera and want to make a spare cable for it. The spacing is 1mm , it looks like a jst sh but i am not sure, it…Continue

PixHawkCube Motor 4 on Main output 5 (has pwm output even when disarmed)

Started this discussion. Last reply by Bert Feb 29. 3 Replies

Hi,Hopefully someone knows what is going on here. For some reason there is no output signal on Main out 4 anymore ( not sure if it causes the crash(minor flip) of broke after the crash ).Swith all…Continue

Camera settings auto or shutter priotity ? (focus manual on endless)

Started this discussion. Last reply by Jochen Reinhard Jun 29, 2018. 1 Reply

Question,On mapping missions do you leave the camera on Auto , or do you set a specific shutter.I have an Sony A6000 with a 20mm lens , i did set the focus on endless but not sure if i should leave…Continue

Skywalker 1900 , gridmission skipping patch and not following waypoints correct

Started this discussion. Last reply by Bert Dec 5, 2018. 24 Replies

Hi all,After alway's flying manual(20 years)  i wanted to help a farmer to do some arial mapping. I have build a Skywaker 1900 flying nice and trimmed manual and also easy to fly in assisted…Continue

 

Bert's Page

Latest Activity

Bert replied to Bert's discussion PixHawkCube Motor 4 on Main output 5 (has pwm output even when disarmed)
"Turned out is was a setting witch channels must be disabled when the save mode is on in mission planner."
Feb 29
Bert posted a discussion

Connector type ( is it jst sh ?)

Hi ,Maybe some one can direct me in the correct way. I have a small connector on a camera and want to make a spare cable for it. The spacing is 1mm , it looks like a jst sh but i am not sure, it looks a bit different that the pictures i found on the web of an jst sh…See More
Feb 29
Bert replied to Bert's discussion PixHawkCube Motor 4 on Main output 5 (has pwm output even when disarmed)
"I did not do any upgrade, this is the only version i had installed. I can't remember the version (3.6.xx i think) . I don't have the device here at the moment. Before posting i did a complete controller calibration , but i only switched…"
Feb 2
Alberto Vila replied to Bert's discussion PixHawkCube Motor 4 on Main output 5 (has pwm output even when disarmed)
"i see that curious , could yo tell me what version of ardupilor are you using and could you repeat this remap in a previous version of ardupilot? maybe you can do the throtlle(radio) calibration with that remap situation.... could you chek the…"
Feb 2
Bert posted a discussion

PixHawkCube Motor 4 on Main output 5 (has pwm output even when disarmed)

Hi,Hopefully someone knows what is going on here. For some reason there is no output signal on Main out 4 anymore ( not sure if it causes the crash(minor flip) of broke after the crash ).Swith all motors and esc's around and the issue must be main out 4. So i was thinking i remap motor 4 on Main out 5. And yes that seems to be working but i do have an constand signal on out 5 (1102 ) even when disarmed . That stop the motor beep but i want the motors to beep all in disarmed state so i know sure…See More
Jan 31

Profile Information

Please tell us a bit about your UAV interest
Everything what flies.
Hometown:
Amsterdam

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2020   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service