Gender
Male
About
Location
Houston, TX
About Me:
retired
Please tell us a bit about your UAV interest
Tri
Hometown:
Houston
Activity Feed
"I have the exact same problem. Did you ever find a solution?"
"I have exactly the same problem. Did you ever find a fix? I fly a 3DR Pixhawk, 3.3 copter, with a minimosd 1.1."
"Steffen, did you ever find a solution? I have exactly the same problem with my 3DR Pixhawk, v3.3 copter. with a Minimosd v.1.1."
"We have the same challenge. My channels 7&8 are used for gimbal knobs. I need to use channel nine to turn my Lidar Lite v2 on and off. It is already setup on AUX 6, pins 54 and 55. I am trying to figure out how to use a TX switch to toggle the…"
"The only change that my Ublox Neo-M8N GPS with Compass seems to need is a wire change on the compass plug. I got 10 sats in 29 seconds, but I cannot get a green light on the Pix. The red wire on the compass plug from the HK M8N is in a different…"
"I am trying to convert my quad to a hex, but the motors will not spin. My logs seem to show that everything is perfect. I got a gps fix while attached to my computer, then attached the battery, then while the tones were playing, I pushed the safety…"
"Thank for the reply, Max. That makes sense. I will preplan that protocol for the next exciting moment. The problem is the instant zero throttle setting. I need to find out what caused that and what will prevent it. It will take me several weeks to…"
My question is, “How can I avoid a repeat?”Log attached.DVR review: While in loiter mode (116 ft altitude, 58% throttle), my quad went into RTL (116 ft, 58% throttle). I clicked into loiter. The throttle instantly reset to zero (111 ft). The quad…
"Okay, I'm brain dead. Switched the new Tx from mode 1 to mode 2. Arms and motors spin.
Johann, thank you for your help."
Johann, thank you for your help."
"Well, it says that there is no need to download that version because it is already on the board. Frustrating. 3.1.5 is on the board, not 3.1.2. It will not let me try to upload it again."
"I have no clue as to which firmware to choose. It appears that there are versions for hexes, tri's, ect. I tried to look it up by clicking on the "download firmwares" icon, but that really gives a lot of confusing choices. Seems that the previous…"
"Thanks, Johann!!! I missed that. I'll let you know how it turns out.
By the way, where are you located?"
By the way, where are you located?"
"3.1.5 copter.
I tried to go to an earlier version in MP but could not figure out how to do it. Is there another way?"
I tried to go to an earlier version in MP but could not figure out how to do it. Is there another way?"
"Johann, thank you for your quick reply.
Yep, that's what I had to do with my tricopter setup. I had to reverse the channel to arm correctly. I did try down & to the left on this quad/Pixhawk setup. It works no better than down and to the right.
I…"
Yep, that's what I had to do with my tricopter setup. I had to reverse the channel to arm correctly. I did try down & to the left on this quad/Pixhawk setup. It works no better than down and to the right.
I…"
Until I updated to the the latest stable firmware for quads, my Pixhawk worked flawlessly. When it would not arm, I changed the arming check to "0" (zero, not O or o), wrote the parms to the board, but the Pixhawk still will not arm. All the lights…
"Ditto. Took an hour to get the green light today."
