Hello,
Is there anyway to connect a HIGH/LOW wire between two Pixhawks such that one can read whether the other is sending a high or low? And if so, which ports would it use? Also, would it be possible to read this voltage in a python script? I have s
Read more…Hello everyone,
Hope you're doing well, greetings of the day. I'm looking to build a hoverbike with Quad propeller with 4 heavy lift motors need design, heavy lift motors, propellers, joysticks, batteries, frame, speed controllers, operating software
Read more…
Hi folks,
Looking for some advice or local experts who might be able to help with a project.
My Municipality (A town north of Toronto, Canada) is looking into building a drone park in a vacant plot of land. Our town has 4 people that are registered c
Read more…I am not understanding why my new build wants to turn over when throttle up!!!
I have solved the esc throttle calibration issue. I have balanced 2 of the 4 props with small pieces of aluminum duct tape and they show very even balance.
My build is curre
Read more…Hi,
I am working on a project that involves sending waypoints to multiple drones at one time through a python script. I know that this can be done because of the swarming work that has been done, but I am unsure of two elements: how to connect multip
I work for a grain cooperative that has a large number of Flat Buildings. For those unfamiliar, flat storage is literally a big empty building that has grain piled to the top. My task has been to use a Phantom 3 Pro to measure the grain in the buildi
Read more…
I had a boat that steals inside there is the gps apm 2.6 there is some way to find it
sorry for my bad english !!! thank you I am building a custom quadcopter based off an Arduino flight controller. I attempted to fly it today. It went about 8 feet in the air, hovered steadily for almost a second, then began to oscillate slowly, then rapidly, then finally flipped over in t
Read more…I have problem with my https://www.aliexpress.com/item/F02192-U-JMT-Assembled-HJ-450-450F-4-Aix-RFT-Full-Kit-with-APM-2-8/ drone wich flips on side or back on lift up.
I have calibrated ESC,Radio, motor an propeller directions and so on. There is no
Read more…I have a Pixhawk with a 3DR Telementry module and when I try to connect to the com 4 I get a time out with the error "no heartbeats received" the pixhawk can connect to the usb using com 3
Tried
different usb ports
different computers
different modules
Di
Read more…Hi,
I just ran into some troubles trying to get my fixed-wing aircraft to work again.
After I had a failure of my rudder during flight I tried to figure out why and then none of my servos responded anymore (lukily on groud allready).
I'm using a PX4 wit
Read more…Hey guysHas anyone managed to get 2 pixhawks to communicate with each other?I want to be able to send the gps coords of my 1st quad to my 2nd quad so that it will be able to follow the 1st quad. The data will be sent via radio.If anyone could point m
Read more…I cannot get the the frame class to quadplane. each time I set it in full parameter list and write params it looks like it saved, but as soon as I reboot the flight controller the setting is back on HEX instead of quad.
I am building a Quadplane and w
Read more…I'm currently having issues with getting the battery monitor to work properly on my Pixhawk 2 Cube from ProfiCNC. I thought that perhaps I had the wrong pins selected, but the Pixhawk 2 manual states they are PA2 for voltage and PA3 for current.
My t
Read more…Hi
I want to assemble a rover run with APMrover2.
Here are the links I found on Amazon.
pixhawk board:
https://www.amazon.com/Weyland-RadioLink-Pixhawk-Controller-Multirotor/dp/B01N4KJEV4/ref=sr_1_3?ie=UTF8&qid=1499973710&sr=8-3&keywords=pixhawk
rover:
hello.
quad turning left and right without touching yaw stick
i`m do not use english, so If i against the courtesy Please acknowledge it beforehand.
i`m flight testing for a month.
arducopter v 3.4.2
problem is my quadcopter is random turning YAW.
pitch a
Read more…I only know a little about quadcopter motors, and there is a question about my motor's thrust. I bought 4 pcs 2305 2450KV motors from a motor online shop, and I got a thrust data on their motor details, but my fridens said the thrust data probably is
Read more…I have a DJI S1000 octocopter powered by a Pixhawk2 running APM 3.4.6 and Mission Planner 1.3.48. When I take off in Stabilize mode, the copter starts to spin constantly on the yaw axis with no yaw (stick rudder) input. The compass has been recalibra
Read more…Now the two compass sensors that most gps+compass module companies stand on is gonna be out of stock soon and now out of production from what i heard
what is the alternatives ?? what is the alternative that pixhawk developers gonna support now ?
is it
