The first drone developed which uses ESP8266 module.
So you would like to get started in drone programming? ESPcopter has you covered. You don’t need to spend a fortune to get started in drone programming. The ESPcopter is a small drone with program
Hi All,
I see this issue has been posted many times....However I post in the hope that someone actually found the answer....Please forgive a rank amateur ...First go.
Assembled my quad copter yesterday...basics achieved eventually...
Using an Ardupilot
Read more…Hello.
I am using the F450 frame.
I am not familiar with electronical engineering stuff.
I want to connect the px4 flow and lidar lite v3 for indoor flying.
I try to connect my lidar lite v3 to pixhawk2.1 follwing ardupilot doc.
My understand is right
Howe
Read more…Hi,
I need help for a simple function in mission planner but can't get how to do it. I am getting input on a channel (say ch 6), and want to output it on any aux channel. I can't directly take it because my output is in PPM. Appreciate it if anyone ca
Read more…Hi Everyone, on the occasion of the launch of my site
www.flyingmods.com
I would like to put the idea of DIY multicopter modding up for discussion:
A lot can be done with the countless, seldom flown and deadly boring quadcopters forgotten in hobby
Futaba T14SG is widely used and here is a way to set six-point switch for flight mode control in T14SG. I have used it in Pixhark and flight tested. It is very accurate and simple.
First go to the 'LINKAGE MENU' and select 'FUNCTION' as below.
Then go
Read more…I have a piezo transducer hooked up to 2 of my attiny85 pins, and I'm driving it via software in AC mode @4khz using a timer and interrupt.
Here is the date sheet of attiny85:
| http://www.componentschip.com/details/Atmel/ATTINY85.html |
I would like to swi
Good evening! I would like to know if anyone has any solution to integrate the Canon G9X with Pixhawk,
since there is still no reliable CHDK firmware. I see some adapted with a cable, but I did not find any
diagram of this adaptation. Thank you all!
Read more…
Dear all,
My pixhawk maybe died after I upload firmware from Qgroundcontrol!
now connect to usb cable happend the error ( connect external usb is same)
Center Led is off
Led B/E on FMU blinking
Led ATC on IO is blinking
Hi, so basically I am going to start a little drone business. I am going to sell a full, unassembled drone kit. In the kit, in will consist of all of the necessary components to fly. Which includes the frame, motor, flight controller, motors, esc, et
Read more…Working with a PX4 and Mission Planner, it "threw a wobbly" and started refusing the MAVLINK connection.
Since I had APM Planner2 sitting on the desktop I tried that and it made connection at the same COM port with the same cable.
I started by installi
Read more…Hey guys!
I'd like to know if any of you have any opinions on open source drones on the market. I'd like to write scripts and codes for drones to complete tasks and objectives such as continuously patrolling an area and landing back at "home" without
Read more…I have a pixhawk that is receiving telemetry messages from my laptop via a serial port. I send the message like so:
int MAVLinkIF::SendAttitudeTarget()
{
// basic messaging set up
mavlink_message_t msg;
int len;
uint8_t buf[MAVLINK_MA
After upload fw onto pixhawk with QGC. So QGC difficult with me, and I trying flashing fw from Mission Planner, but some thing error in Usb ( the pin of USP maybe not tight, when I keep my hand it can connect. But when my hand strong, Usb take out. I
Read more…I want to do a project with a drone transmitting a picture which is then relayed to a website automatically. I expect there to be an intermediate step with a smart phone or maybe an arduino.
The drone camera sends the picture over Bluetooth (I assume)
Read more…Hi everyone!
I'm working on a MP script for a few drones. I have takeoff, landing, and safety pilot stuff checked out, but I want to control a servo (or basically anything that runs on the AUX lines from the pixhawk) through the script. I'm having iss
Read more…Hey Everyone,
I'm just looking for some help on a problem I recently stumbled upon. I have been using a Pixhawk 1 with ArduCopter v3.3.3 and a Futaba R7008SB RC receiver for some time now with no issues.
I recently purchased a Pixhawk 2.1 and have not
Read more…I have a Mobius mini I am using as fpv camera. I am using lawmate 1.2ghz tx/rx. I am getting signal to my immersionrc screen no worries. The problem is I cannot get a signal on my usb capture device. When I use my 5.8 GHz system no worries. All works
Read more…Sky Eye-30UZ consists of 20MP 30X optical zoom camera and a 3-axis high stabilized gimbal which will allow you to capture details when you are far away from the object.Equipped with the 1/2.3 inch 20MP SONY Bionz X sensor,Sky Eye-30UZ is able to take
Read more…