Hey Guys,
I have a drone hire website that I have been working on for over 8 months--I just completed it. www.DroneTrades.com is a drone hire and buy/sell used and new drone site. It is free for anyone to create an account. Please support me and crea
Read more…Hello everyone. I want to ask how to configure the pixhawk Failsafe. Taranis my radio has a range of 2km and my rfd900 telemetry is 15 km. In an automatic mission with more than 2 km and less than 15, the Taranis initiate a Failsafe although rfd900 h
Read more…Hoping someone can point me in the right direction… no pun intended.
Done all the calibrations, have a good GPS lock, etc, etc, etc. When I go into loiter mode it wants to start to bank left and slowly fly off. Sometimes it even does weird things wit
I have throttle nudge turned on. When I change the throttle to particular values it can cause the TECS to go crazy with the pitch and throttle control. Here is a log clearly displaying this:
https://www.dropbox.com/s/8i26l1z01nrndji/4.BIN?dl=0
Having t
Read more…Hi,
I have a serious problem with the loiter mode on my Quad
Setup:
APM Copter 3.3.3
FC: AUAV-X2
Compass: HMC5883L (Module) mounted on a mast above the FC
GPS: Banggood GPS Module (not using the compass with this module because it does not work):
Read more…Dear modelers,
I need an older version of Arduplane hex to upload do my board: up to 3.2.3, as newer versions don't have the camera mount code for APM 2.5, but can't find it on mission planner or at http://firmware.ardupilot.org/ , only newer versio
Hey all, I'm wondering if anyone can help give some guidance on a weird Altitude Hold issue I am experiencing. I am running a Naze rev5 Full FC with cleanflight on a TBS Discovery frame with Cobra 900kv engines. I finally have alt hold working dece
Read more…I am sure many of you have had the same issue but I am wondering what strategies you take to minimise this issue.
To illustrate. I have a flight with 312 images (taken with a sony a5100 from a skywalker 1900 and pixhawk fc). When using georef I get t
Read more…I am working on a build using a HK retractable landing gear that is rubbish. It is giving me headaches from day one actually. It rattles and is flimsy. Therefore i would like to set the landing speed to 15cm/s. If i try this i get the message that th
Read more…Hi guys, we are doing a drone which has 12 motors, 6 on top and 6 below acting as a coaxial configuration. I would like to seek assistance for configuring such drone in mission planner.
Read more…Hello,
I am trying to use a RPi 2 and a Pixhawk to run a computer vision algorithm which then inputs flight commands to ArduCopter 3.3. I was wondering if there was a way to do this without having to go through mavproxy as the flight commands will nee
Read more…I have ppm configured on 3 quads using a eachine racer 250....apm 2.6 f450....and Pixhawk s500.....problem is i cannot get anything else to work...besides the quad controls and flight modes..i don't want to use pwm....could someone please help me? I
Read more…dear all:
I've met a crazy and dangerous issue again, my copter flied to the sky and out of control.
Firmware: RC3.3 ArduCopter
Copter: octa, Agricultural Copter with 10kg water.
Issue:
first time,:
Read more…All,
I have developed a Windows GUI for 3-axis magnetometer calibration (see screenshot below), and it is available for download at https://github.com/paynterf/MagCalTool. The tool accepts comma, tab, or space-delimited magnetometer data via a select
Read more…hi folks,
I have a pixhawk PX4 and am developing a control program for fixed wing plane and wanna to test it with simulator XPlain 10. I found manual for connecting QGroundControl with XPlain (in attachment). But in that manual QGroundControl v. 2.0.0
Read more…Hello
I just built my first copter with the following configuration
Hexa copter
APM 2.6
GPS with on board compass
firmware version is 3.2.1
I have setup and calibrated everything but it keeps on flipping front to bottom
Here is a video
Read more…Hi guys, we are building a 12 rotor copter but mission planner does not have the frame type for the 12 rotor. I would like to seek assistance for configuring this 12 rotor motor. Thank you.
Read more…Hi. Had a flyaway today. My heavy hexa (11kg) with Pixhawk ArduCopter 3.3.3 crashed into a tree after something failed in RTL sequence.
After analyzing all info in both dataflash and tlogs, I can not find anything wrong. RC Connection was lost and the
Read more…Hello,
I am trying to find a drone similar to the 3DR Solo that uses mavlink and WiFi similar as Solo but I am hoping the manufacturer is not 3DR. Any suggestions would be greatly appreciated.
Thanks in advance,
Joe
Read more…Just over 3 years ago, we had a challenge finding an affordable portable digital video recorder (DVR) to pair with a monitor for FPV. We end up with a Angel Eye DVR made for security cameras to pair with a Sharp portable analog TV (that quickly beca
Read more…