Just wondering if it would be safe to do a compass calibration on one of many identical drones in one location and then copy those values to the other drones without needing to calibrate all the drones? Should the values be identical if the drones a
Read more…looking for some recommendations on the items I need
This is what a currently have ready for a aerial Drone
4 4000 mah 6 s batteries
1 Tarot Carbon Fiber Frame FY690S TL68C01
6 4910 380KV motors with props
1 Sony A 3600 DSLR Camera
Could you recomme
Read more…Hello all. I've been operating quadcopters (and a hexacopter!) for a couple of years now for my company, and lately I've encountered a new challenge that such vehicles are not capable of performing.
I have arrays of photovoltaics that have serial numb
Hi all,
What software is used to program autopilot controllers like APM2.6 and Pixhawk? I searched and I found Arduino Integrated Development Environment is a program used for micro-controllers. I am not sure if I can use the program to code for APM2.
Read more…3D walkthrough animations are the best way to market your projects. It helps any investor before making any major financial investment in any property project.
High quality photo realistic 3d animation services & 3d walkthrough services in Delhi, Noi
Hi Folks;
I am building an octocopter from scratch. It is at the point that it looks like it is ready to fly. The motors idle, run up to max and change speeds depending on whether I use the jaw, pitch or roll. I have no error or warning messages in Mi
Read more…Hey Guys! I have a desk job of data entry and that's why I have to work daily 6-7 hours on monitor. Now my eyes are getting so stressed and that's why i am unable to focus on my work. Please suggest me some monitors that can protect my eyes from gett
Read more…*Strange* ..My PlayUav osd is only showing 00 numbers of telemetry suddenly in my Fatshark googles.. Been working perfect 2 years. When connecting pixhawk direct to pc with USB and Misson planer , it show actual telemetry numbers.. What could be wron
Read more…I’m trying to get a +5v output on my Pixhawk mini, simple I thought, nope. The Holybro Pix Mini does not have any aux ports.
ALL I need is a channel either on the jumper R8 receiver or on the pix to flip between 0v and 5v when I operate a switch on my
Read more…Hi guys,
When an drone crashes and the propellors hit the ground do the ESCs get damaged. My drone crashed one while I was flying and motor 1 hit the ground along with the propellor. The motor was damaged so I replaced the motor checked and the esc1 s
Hi guys,
When an drone crashes and the propellors hit the ground do the ESCs get damaged. My drone crashed one while I was flying and motor 1 hit the ground along with the propellor. The motor was damaged so I replaced the motor checked and the esc1 s
The double refrigeration technology in the Chest Freezer Factory has solved the technical problems that cannot be overcome by a single refrigeration method, thus leaving no refrigeration blind area in the freezer. Ultra-wide shelves provide customers
Read more…Hi, everyone!
Not really a DIY thread (yet...), but I think here is enough knowledge to help me out with my project.
I've recently found this drone in the woods. I've brought it home. No battery charger, no controller, no rotor shields.
Before spending
Good day everybody ! Hope you are all doing well ! I am new on this forum and I am looking for solutions for my problem:
I am building a drone and I would like to connect my flight controller (Openpilot CC3D) to my RC receiver (Windbox receiver 12ch F
Read more…I am using pixhawk 1 with arducopter.I want to get it to work, so that the pwm output pulsewidth is zero, when ardupilot wants the motor not to run and that the pwm pulsewidth is max (the duty cycle is 100%) when ardupilot wants the motor to run at f
Read more…After Greetings,
https://www.linkedin.com/pulse/integrate-drones-different-use-cases-secure-improved-channels-hassan/
Here is the link to my linkedin article , your feedback would be helpful ,
Thanks for your time , Ahmed Alaa Hassan.
Read more…Hello,
We are building a drone Lidar dedicated for confined space inspection. The Lidar module is self-powered, light enough for small drones, and provide high accuracy point cloud. It has much lower SWAP (size, weight, and power) and cost, compared w
Read more…Hi Everyone,
Years ago I was flying missions and I still have the hardware. I was thinking to try again but this stuff is old. I wanted to know should I rip it out and start over or try to resurrect this stuff?
I even have an old rembizi OSD. honestly
Read more…