I am using pixhawk 1 with arducopter.I want to get it to work, so that the pwm output pulsewidth is zero, when ardupilot wants the motor not to run and that the pwm pulsewidth is max (the duty cycle is 100%) when ardupilot wants the motor to run at f
Read more…After Greetings,
https://www.linkedin.com/pulse/integrate-drones-different-use-cases-secure-improved-channels-hassan/
Here is the link to my linkedin article , your feedback would be helpful ,
Thanks for your time , Ahmed Alaa Hassan.
Read more…Hello,
We are building a drone Lidar dedicated for confined space inspection. The Lidar module is self-powered, light enough for small drones, and provide high accuracy point cloud. It has much lower SWAP (size, weight, and power) and cost, compared w
Read more…Hi Everyone,
Years ago I was flying missions and I still have the hardware. I was thinking to try again but this stuff is old. I wanted to know should I rip it out and start over or try to resurrect this stuff?
I even have an old rembizi OSD. honestly
Read more…Can anyone tell me if it is possible to control my Movi M5 gimbal using my Taranis X9D+ transmitter and X8R receiver?
The Taranis X9D+ is not on the list of controllers recommended by Freefly for the Movi M5, but then I see other gadgets which can con
Read more…Hello! Who can share firmware for 3.8.5 aircraft? Very necessary. PIXHACK V.2 controller. My mail is ruslanaviakit@gmail.com
Read more…3D walkthrough animations are the best way to market your projects. It helps any investor before making any major financial investment in any property project.
High quality photo realistic 3d animation services & 3d walkthrough services in Delhi, Noi
I not sure this is the best forum for this post. I f there is a better place let me know.
Thanks all in advance for helping me get my drone working!!!
I am a Newbie building my first quad and first time playing in the RC world. My problem is I can’t g
Read more…Hello !!
I have a problem with my Drone (Quad X) when i want to make my ESC calibration.
My hardware :
FC : Pixhawk PX4 2.4.8
ESC : Blheli-S 30A
Moteurs 220S 2550KV
Radio commande : FS-I6X
Recepteur : FS-IA6B
When i make calibration with mission planner, the
Read more…Well, I'm in over my head. Mostly a mechanical guy but decided I might be handy enough to build a drone. Well the frame is built. Haha. Now I'm stuck with software.
Okay, so I have the NAZE32 v6 board and Betaflight. I've also downloaded the reco
Read more…Hi everyone,
To start, please be patient with me. I know enough to know I don't know what I'm doing right now, so that is a start.
Bottom Line Up Front: I can't connect my drone to my computer and can't get the controller commands to register on the Na
Read more…I have been wanting to build a quad or hexcopter for about 10 years now. I've owned a few drones with GPS but they were low end toys that always ended up in my or someone's lake. I was asked by security not to swim in the lake anymore... Lol
A little
Read more…Hello everyone!
I'm working on a project related to autonomous and piloted flight and image recognition missions of a hexacopter, which is being very difficult due to a lot of problems to configuring the command for "Yaw" in the radio with Mission Pla
Read more…Hallo guys,
I already have a Mavic 2 quadcopter, and am looking to build a fpv fixed wing drone, with the following requirements:
It should perform long range missions, using both radio and 4g/lte connection, stream video and be manually controllable o
Read more…hello all, I have 2 e32-433t20d I wanted to try the qczek system on rc groups last weekend but a friend of me who is a communication engineer was around he saw me working with the modules so he proposed to set those e32 lora 100mw I have to send te
Read more…Hi!
I have 3 RFD900x. I use them as node 1, node 2 and node 3. I want to node 1 and node 3 communicate over node 2 even if node 1 and node 3 in range. I followed RFD Multipoint DataSheet bu didn't work. Please advise me to solve this problem.
Read more…Where is the best places to store documentation related to a project in Microsoft Azure Tutorial? Currently team members are uploading documents (excel, word etc) into a repo that has code in it which is not ideal. What is the recommended approach to
Read more…Hi
I'm working on designing and building a multirotor drone to lift a ~3kg payload with a group at my university. My role is to help design the frame, and while I have a few ideas, I need some advice on the best way to get to a finished design.
Obvious
Read more…Hi,I was hoping to use UGCS with a DJI m210 RTK v2.Their web page lists the m210 RTK v1.Does anyone here know if the v2 drones work?Thanks,Steve
Read more…