Hi, I had a strange flight today, I tried the logs but was not able to diagnose...
I did a first successful flight and run auto tune no problems at all, then I attached a gimbal, and moved the battery to a new position to re-balance, the flight starte
Read more…I am getting Bad Lidar Health warnings, but good sonarrange data when I attempt to test a LIDAR-Lite on my Pixhawk running MP 1.3.30 and ArduPlane V3.3.0 .
Is anyone else experiencing this problem and is there a solution?
Read more…Just carried out my first autotune on my Extended F550 (680mm motor-motor) hexacopter. Completed in just over 10mins and I must say the copter feels a lot more dialiled in now. Just got home to hook it upto MP, and to my surprise, the Stab P values a
Read more…I've been troubleshooting Altitude loss in primarily forward flight. Left or Right roll into a wind results in the same altitude loss as well as being more pronounced when flying into the wind in forward flight. Backwards flight seems to not suffer a
Read more…Since my previous thread dried up, I thought I'd do some more testing, and see if the symptoms triggers any memories and possible solutions.
Got a hex running 3.2.1, with spektrum PPM receiver. APM 2.7.2 from HK but with 3DR GPS. All calibrations done
Read more…I want to know from the experts out there would it be possible to create a WiFi data logger using Raspberry Pi (or other inexpensive embedded computer) to monitor and record charging information from an inexpensive battery charger like the X120 from
Read more…Anybody have any resources for rules/laws/regs on operating drones commercially in China?
Thanks!
Read more…Hi folks,
I have a Pixhawk connected to a 3DR telemetry radio and a Minum OSD, using the Telem 1 and 2 ports, and I now want to hook up the FrSky/Taranis telem adapter board.
Do I need a telem y cable to make this work?
What is the best way to hook up t
Read more…Hi,
I am stumbled with an odd situation.
I am using Zippy 25C 4S batteries for smaller craft that drains 13-14A at loiter and decided to use them in parallel for a Tarot 690S that uses 4006 680kv motors.
this is a 3kg platform now and it draws around of
Read more…I have two motors driven by Turnigy Multistar 30 Amp BLHeli Multi-rotor Brushless ESC 2-6S V2.0.
Connected via a Y-cable to the Pixhawk port 3.
When everything is connected and the system is powered up the motors refuse to start when armed.
If I detach
Hi everyone! I wanted to throw an idea out there to hopefully have someone respond and say "this already exists". If not, then I hope it can start a discussion that could lead to something that I think would be really neat.
In flying my hexcopter and
Read more…Hello everyone!
After the ardupilot forum is NOT working (I don't get an e-mail for the account approving, of course I checked the spam filter, I actually tried it with two different e-mail adresses) I try it in this forum.
I mounted the ArduPilot on a
Read more…Hello everybody,
I am a newbie into the world of UAVs/multicopters and after reading and reading a lot of stuff and useful information I need to start sorting things out inside my head. Therefore, I need the help of the experienced guys to make sure t
Read more…Hello
I'm using EZ cap and trying to have an overlay of the video on the HUD.
when i start the video the HUD roll starts to jitter.
I've checked .. there is no RF/EMI interference... all seems to work well.. but the overlay,
I have a laptop PC with WIN X
Read more…Hi.I am new here.But I love DIY stuff and really admire the work u guyz have done here.So I was Wonder around the web searching for new rc transmitter and came across this http://headrc.com/tv/photo/yuneec01 I was fascinated by this android based rc
Read more…I am trying to change my "sr1" settings in the mission planner setup.
I make a change and upload them. The changes do not take.. If I read the pixhawk config, they are on different values than I set.
I found some old posts where people had this is
Hi there, I have been running dual GPS's since I found out that the support had been added. But I have not seen anything in mission planner, or a log to say that the GPS switch is actually happening. Yes I have gps auto switch turned on and set both
Read more…Is there any way to adapt a minimosd-extra character set to work with arducam osd? I have tried to load the newer character sets while running the older arducam osd frimware but the osd is all jumbled up so something is definitely different between t
Read more…So, I built my first quad with 18" separation between motors on the X and Y plane. It's in an "H" quad configuration with custom built frame and I'm using the CC3D copter controller. The problem seems to be when I YAW left or right it's WAY too sen
Read more…hi, i would like to know what and how the format of data long looks like when written on bin file in px/apm. i have tried writing one on my own using Arduino IDE but it did not work out. i tried including the headers, followed by the parameters like
Read more…