In order to find the problem with my yaw issue I'm using the log. Dowloading is no problem. But when I want to browse the logs, all are 0kb. When viewed in notepad its blank.
Now I copy paste the data into a new log extension file and can view the log
Read more…Hi,
I'm anxiously trying to setup my scratch-built quad using the mission planner as recommended in the documentation.
I've downloaded the most current APM Planner 0.4.37, but when I go to Actions->Upload firmware, I get a window popping up saying "F
Read more…Hello all!
I bought the APM recently from DIY Store and soldered it up. However, when I connect it to the APM Mission Planner for its initial start up, the PC shows the prompt that it cannot upload APM version, please check cabling. What does this me
Read more…Hi there, I need to conect Xbee with IMU sensor board, but breakout board on back order, is there any way to connected it with out it?
Read more…For those of you already using the Ardu-pilot Traditional Helicopter, I have a few questions.
1. Can it be used with a flybarless Helicopter?
2. If so, does it compare to the other FBL control systems out there(Only talking about stability, no autonom
Read more…Hello,
I've been holding off flying my new stock AC2 quad since some early successful flights with 2.0.5, waiting and watching the yaw issues being resolved etc. It seems pretty good now by most reports, but there isn't much detail about people's cur
Read more…Hi All, I am currently in the conceptual phase for a MAV design. I wanted to know if a pressure sensor will be needed to implement the altitude hold or is the GPS good enough for low altitudes? We have to fly it for ten minutes, probably a distance o
Read more…Hi EveryoneI want to use QGroundCOntrol on my Ubuntu laptop. However there doesn't seem to be a download link for linux at this site.https://github.com/pixhawk/qgroundcontrol/downloads/So where do i get it?ThanksSrinath
Read more…Hi,
I that there are 4 serial ports on the ArduPilot Mega. Are any of the ports free? I know one of the them is used for the Xbee connection and I was wondering if I could use a free serial port to communicate the aircraft state(IMU and GPS) to a micr
Read more…Hi guys!
Thanks to Jason for enabling the AM mode in the default code (from planner) version 2.0.16 and above
#define MOTOR_LEDS 1 // 0 = off, 1 = on
#define FR_LED AN12 // Mega PE4 pin, OUT7
#define RE_LED AN14 // Mega PE5 pin, OUT6
#define RI_LED
Hi there, I traying to have my UAV proyect running, but after all electronics installed an tested, sudenly
my esc is warning and getting arm keep beepeming full trotle stick, Rc electronics is ok, I just reload
firmware, erase eeprom, same results esc
Read more…I'm amazed, after a day of assembly and two days of configuration and figuring stuff out, I had my first flights today - works great. One thing I learned is not to turn the transmitter off with the motors armed! It didn't get far ;-)
Very stable, run
Read more…Hi everyone. I'm a bit confused about ArduCopter 2. Is there new hardware or the name came because of some software update?
I have bought the Jdrones Arducopter 1.1 Kit and I don't know what I need to do in order to update it to version 2. I understa
Read more…Hi EveryoneI got these 2 xbee's second hand.How do i figure out their operating frequencyThanksSrinath
Read more…Here is my new quadcopter. The max dimension is 185 mm (tip to tip).
The video from the first outdoor flight is shown here: https://www.youtube.com/watch?v=Un_guPJ1Qoc
Some details:
- weight 170 gramm
- propeller AirAce 3-blade left/right, motor Hacker
Hi EveryoneCan i use a 3G phone to send live video from a uav to a ground station?The possibility seems interesting for increasing the tx range.This way, you reduce the wt and power consumption of a large tx, and instead your data just hops from 1 ce
Read more…So after a little confusion (reading the rev B instructions with the rev C board), I've got my power board under construction.
Soldered my power connections (12 gauge wire to the middle, and have soldered deans sockets all around. Took great care tha
Read more…For the last 5 years I've been trying to find a good sunlight readable screen for operation in the Mojave desert.
Until last month I'd failed.
I'd heard good things about the http://www.pixelqi.com/ screens.
I'd never seen one and after being disapoint
Hi everyoneHere is my first try at a uav taking pictures.I bought this camerahttp://store.diydrones.com/Micro_Compact_Super_Vision_CCD_Camera_p/cam-0003-01.htmHow do i connect it to the APM board and beam back pictures?Can i use the Xbee data link to
Read more…