I have a Futaba 6EX which has two 2-position switches on channel 5 and 6. I am unable to mix them to form a 4 position switch according the Futaba (marketing or honesty?) so how do I create more positions on my switches?
Why not use an Arduino Pro Min
Can someone tell me what is the difference between these quads?
Do they use the same boards?
Greetings everyone. I'm working on a project where a computer steers a farm tractor via GPS. Getting accurate position data is easy. My challenge has been getting accurate heading data. I have tried a MEMS gyro on the yaw axis, but it shows a lot of
Read more…hi all friends,
i have started to build my quad rotor with arduimu v2 flat,i was looking thruogh the code,initially i am using arduimu v2 flat as a main circuit board and future scope for magnetometer and gps module,and accordingly i set the parameter
I am interested in using ardupilot in a rc car and believe in needGpsArdupilot itselfBut I have read the user manual and it does not mention how to do it for a car.Also, is there a way for it to respond to the ground beneath it or control it's speed
Read more…Ok guys, I am COMPLETELY new at this, so please forgive me and feel free to shoot holes in this.
I am wanting to build a drone that is pretty hefty and could drag up a forward looking video, full autopilot, downward looking video, and downward looking
Ok I received the mq9 from nitroplanes as a gift not sure if this is best format for ardupilot. This thing has a 8 ft wingspan! Is this going to be a nightmare for my first ardupilot project ?any suggestions greatly appreciated thanks-
Read more…Guys,
I'm a little confused as to what and how to set-up a 3 pos switch. I would like the 3 positions to be:
Manual
Stabilize
RTH
The Arduino interface says:
If you only want 3 modes set 1=2, 3=4, 5=6 and set your switch to produce 1165, 1425, and 18
Read more…Hi,
At last I managed to go out flying with ArduPilot Mega.
I was setup with:
- Skywalker : http://www.rcgroups.com/forums/showthread.php?t=1223595
- APM +OilPan and no AirSpeed sensor yet
- Ublox GPS
- 3 modes : MANUAL, STABILIZE, RTL
Worringly, with the
Hi guys,
I'm a video game programmer (focusing on artificial intelligence) and I'd like to take some of the concepts I've had a chance to experiment with in virtual worlds to our very concrete world. I'm interested in building a "multi propeller" cop
I'm using 2.4Ghz rx/tx.
Using 900Mhz for telemetry.
Question is, since the rx/tx is spectrum, shouldnt I also be able to use 2.4Ghz for video, or would it stll cause interference?
If so, what frequency would be good otherr than 2.4 and 900?
Finall
Read more…i am trying to conduct the tests before i fly my skywalker.
i have test flown my plane without any gear and have now just installed all the ardupilot.
on the test page http://code.google.com/p/ardupilot/wiki/Test
i have tried inputting 1 into my arudpil
Easystar noob here.. After upgrading my ESC to extended-length motor leads, I'm trying to tuck these three 16ga silicone wires into the Easystar fuse before gluing. The existing channel is not deep enough to hold them.. maybe two at the most.
Do mos
Hi there,
I'm reviewing the code whilst finishing off on the last details on the APM (voltage monitor, xbee connection, etc.) . I noticed that the APM makes rather heavy use of the eeprom also in flight.
From what I gather, the eeprom is written to a
Hi all. It seems you have some experience with this Easystar platform..
I'm building one just for ArduPilot, and starting with brushless..
I have a Castle Phoenix-25 and Meag ACn 16/15/4 (2200kV) motor.
I ran an APC 6x4 Electric Pusher prop on the benc
hi
Hallo,
i play with idea to equip my airframe with ardupilot but i need to control ailerons by two separate channels. Is there any ardupilot modification with such feature?
In description i saw only one channel for ailerons ;o(
Please tell me where the different props should be mounted.
Should the push props be forward and back or left and right?
Thanks
Read more…