Gender
Male
About
Location
Combrit, Brittany
About Me:
Retired Air Force Transport Pilot. Back to R/C models since retirement.
Please tell us a bit about your UAV interest
Quad and Y6 Copters.
Hometown:
Combrit
Activity Feed
"Naze32 is good "obsolete" control card.
Rule of thumb weight:
1/4 frame and accessories,
1/4 motors and esc and propellers
1/4 battery
1/4 payload (cam, gimbal, video tx,...)"
Rule of thumb weight:
1/4 frame and accessories,
1/4 motors and esc and propellers
1/4 battery
1/4 payload (cam, gimbal, video tx,...)"
"You get it,
RC transmitter send commands to the flight controllers (Up, Down, Right, Left,...). Flight controller send commands to the motors.
https://www.rcgroups.com/forums/showthread.php?2429327-Basic-Introd...
Enjoy,
Marc"
RC transmitter send commands to the flight controllers (Up, Down, Right, Left,...). Flight controller send commands to the motors.
https://www.rcgroups.com/forums/showthread.php?2429327-Basic-Introd...
Enjoy,
Marc"
"Octocopter or Quadcopter, the radio settings are the same.
Follow the wiki: http://ardupilot.org/copter/docs/common-rc-transmitter-flight-mode-...
All pertinent information is there.
Pixhack 2.8.4 is not a Pixhawk. It is an adaptation of an old…"
Follow the wiki: http://ardupilot.org/copter/docs/common-rc-transmitter-flight-mode-...
All pertinent information is there.
Pixhack 2.8.4 is not a Pixhawk. It is an adaptation of an old…"
"Not easy.
I have some modules (3DR or equivalent) and Comport is USB Serial Port (FTDI), version 2.12.0.0 26/08/2014, on a W10 setup. Dan Beich said:
I can now confirm it's not a port issue. I tried another computer's ports and I got the exact…"
I have some modules (3DR or equivalent) and Comport is USB Serial Port (FTDI), version 2.12.0.0 26/08/2014, on a W10 setup. Dan Beich said:
I can now confirm it's not a port issue. I tried another computer's ports and I got the exact…"
"Red blinking is data transmit.
When the two units are connected (mission planner), the two units have red light blinking. If connection is not established, ground red (near the serial plug) is off.
It could be a bad COM port selection or Serial 1…"
When the two units are connected (mission planner), the two units have red light blinking. If connection is not established, ground red (near the serial plug) is off.
It could be a bad COM port selection or Serial 1…"
"Steady green indicate the two units are paired.
Can you look at https://docs.emlid.com/navio2/common/ardupilot/installation-and-run...
and confirm Telem2 line is uncommented in your arduxx file.
If there is also a micro usb plug on the air unit,…"
Can you look at https://docs.emlid.com/navio2/common/ardupilot/installation-and-run...
and confirm Telem2 line is uncommented in your arduxx file.
If there is also a micro usb plug on the air unit,…"
"Hello,
Parameter reversed: could be part of QGroundControl radio calibration process.
Motor problem: It also could be a bad ESC calibration. You can redo ESC Calibration with a receiver and a 4 in 1 plug or repeat the process for each ESC.
Marc"
Parameter reversed: could be part of QGroundControl radio calibration process.
Motor problem: It also could be a bad ESC calibration. You can redo ESC Calibration with a receiver and a 4 in 1 plug or repeat the process for each ESC.
Marc"
"There is something. In the Edge RC settings, RC2 (Pitch) is reversed. It should not. You have to reverse the Pitch channel of your RC Tx. You will have to redo the RC Calibration after changing your RC Tx settings.
RC1_MIN
985
RC1_TRIM
1501…"
RC1_MIN
985
RC1_TRIM
1501…"
"Hello,
Try to share your .bin file (downloaded from Edge). From first look at the .log file parameters, you use default parameters.
Can you share a picture of your quadcopter (from above) and confirm Prop size and take-off weight.
Best place to…"
Try to share your .bin file (downloaded from Edge). From first look at the .log file parameters, you use default parameters.
Can you share a picture of your quadcopter (from above) and confirm Prop size and take-off weight.
Best place to…"
"Hello,
See Rally Point feature,
http://ardupilot.org/copter/docs/common-rally-points.html#overview
Marc"
See Rally Point feature,
http://ardupilot.org/copter/docs/common-rally-points.html#overview
Marc"
"ContraRotation on a flat Hexa or Octa is for Yaw control.
Developpers choose to have contrarotatings motors on Y6 then Octo-Quad X config for thrust distribution staying even during Yaw.
As 12 motors control card are not common on the market, your…"
Developpers choose to have contrarotatings motors on Y6 then Octo-Quad X config for thrust distribution staying even during Yaw.
As 12 motors control card are not common on the market, your…"
"Hello,
If you google "R7008SB pixhawk" you will find old information with your same problem.
I have a 18SZ (had a 14SG) and I do not use R7008 or 3 sBus2 receivers on my multicopters, but R6202SBW or R6303SB. I have telemetry via 3DR radio.…"
If you google "R7008SB pixhawk" you will find old information with your same problem.
I have a 18SZ (had a 14SG) and I do not use R7008 or 3 sBus2 receivers on my multicopters, but R6202SBW or R6303SB. I have telemetry via 3DR radio.…"
"? What is your Arducopter card ?
No sBus in with APM, only PPM
?? Is sBus Rx mode configured ??
See Futaba Rx user manual for that,
Marc"
No sBus in with APM, only PPM
?? Is sBus Rx mode configured ??
See Futaba Rx user manual for that,
Marc"
"The data source available I found was here:
http://tfr.faa.gov/tfr_map_ims/html/ns/scale3/tile_1_2.html
and looking at Oregon, one lousy spot in the middle of the state.
T is for Temporary. For permanent information, you have to look at sectionals…"
http://tfr.faa.gov/tfr_map_ims/html/ns/scale3/tile_1_2.html
and looking at Oregon, one lousy spot in the middle of the state.
T is for Temporary. For permanent information, you have to look at sectionals…"
