About

Gender

Male


Location

Federal Territory


About Me:

A newbie in UAVs.


Please tell us a bit about your UAV interest

Quadcopter,Floater Jet,Cessna Scale Trainer & Skywalker.


Hometown:

Kuala Lumpur


Activity Feed

Mie Must posted a discussion
Hi, need help of pairing the Pixhawk with Optima 9 receiver. Already success the  firmware upgrade (v3.01) via HP-22  for both receiver and 2.4 module as per the wiki…
Jan 16, 2015
Mie Must commented on James Cartwright's photo
"Hi, nice frame u got there. Any link?"
May 18, 2014
Mie Must commented on Gary McCray's blog post Some MultiCopter Design Thoughts.
"Hi, interested to know on how do you test the prop/thrust efficiency, is there any software for it? I'm interested to test mine as well.TQ"
Jan 23, 2014
Mie Must left a comment for Kenneth Tan
"Youre most welcome Kenneth"
Jul 23, 2013
Mie Must left a comment on DIY DRONES MALAYSIA
"Sorry Meez for the late reply, welcome to te group. We are quite active in Diy Drones Msia fbook with over 400 friends fr all over the world. Maybe theyre more comfortable over there. Anyway APM2.5 is really a few steps ahead compared to APM1.…"
Mar 22, 2013
Mie Must commented on elad orbach's blog post How to DIY a ground station
"Very neat set up. I'm envious!"
Feb 13, 2013
Mie Must left a comment for Mohamad Hafidz
"Assalam Mohamad, sorry to say that i already dismantled mine. I DIY n tried many APM based multirotors and found out that Octa V has poor Yaw control but managed to get a pretty stable flight. Already tuned it to the max and loosing my hair but its…"
Feb 13, 2013
Mie Must commented on elad orbach's blog post How to DIY a ground station
"tecnically creative"
Feb 8, 2013
Mie Must replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released
"My 1st attempt:
1. Its a li'l hassle when doing the accel calibration especially when using frame other than quad ex-Y6. Can it be as simple as the previous version? I tried my Y6 and couldnt get a proper reading. Placed it on a flat surface and…"
Jan 18, 2013
Mie Must replied to Andrew Tridgell's discussion Welcome to the 3DR Radio forum!
"Hi, I am going to replace the standard 2dbi 433mhz 3DR antenna coz the signal is limited about 100m. What is the best replacement for the air and ground antenna so the data it can reach up to 3km?"
Jan 3, 2013
Mie Must posted a discussion
Crashed my Quad yesterday at the height of 35ft due to battery failure. It fell horizontally and the impact caused the top carrier which carry the Ublox gps came off forcing it to pulled the cable and dislodge the gps port located at the bottom…
Nov 24, 2012
Mie Must posted a discussion
http://www.youtube.com/watch?v=rAs0-IU4PrUSharing my APM 2.5 performing Loiter 360 panoramic aerial video without gimbals and image stabiliser apply.Recorded on gopro 1080hd then converted to 720 for faster upload.Fr my opinion this board is really…
Oct 3, 2012
Mie Must posted a discussion
I tried the AUTO mode on APM2.5 and load my Quad with firmware 2.7.3  and then created 6 points for a start.1st to 4th point it when well when it reached 5 point the copter slowly decend itself even though the altitude set was 10m. Forced me to…
Oct 1, 2012
Mie Must posted a discussion
Hi, my CIRCLE mode turn out to be a bit jerky and wobbly and i have no idea where to tune. Its a multi- cool mode and I like it. Thanks to the developers. Should i tune the ROLL or YAW? Anyone having the same issue. Need some tips here guys. Below…
Sep 25, 2012
Mie Must replied to Jeff Smith's discussion Optical flow on APM 2.5, where to land it?
"Problem solved for APM2.5 OPTICAL FLOW wiring 
http://code.google.com/p/arducopter/wiki/AC2_OptFlow"
Sep 17, 2012
Mie Must commented on Klaus Heinrich's photo
"Hi Klaus, thanks for adding me in your fB. My compass showing NOT HEALTHY in CLI mode. Already resoldered the blob and now it shows the reading. Preparing for the 2nd flight test this weekend. Share us some videos too my friend in DIY Drones…"
Sep 4, 2012
More…