Gender
Male
About
Location
Smolyan
About Me:
Engineer of electronics. Making airplanes sinse 1967.
Please tell us a bit about your UAV interest
Building a version of Gentlenav with different gyros.
Activity Feed
"No, the same sensors as of the Pixracer, but HMC5983 which is obsolete and there is no equivalent on the market.
I hope that the code porting will not take long as the MPU9250 and ICM20608 drivers are well developed and working fine in Pixracer."
I hope that the code porting will not take long as the MPU9250 and ICM20608 drivers are well developed and working fine in Pixracer."
"Hi Cala,
The holes are semiholes as the width is just 30mm while the holes grid standard is 30.5 x 30.5mm.
As we plan to offer a housing and housing STL files, we'll design a tight mounting even with semiholes."
The holes are semiholes as the width is just 30mm while the holes grid standard is 30.5 x 30.5mm.
As we plan to offer a housing and housing STL files, we'll design a tight mounting even with semiholes."
"Hi guys,
Sorry for not participating lately, but we ( Bulgarian users ) couldn't access DIYDrones for a while for some reason.
Today I gained access of it again....seems someone fixed the problem.
About X2.1....I ported the bootloaders for both FMU…"
Sorry for not participating lately, but we ( Bulgarian users ) couldn't access DIYDrones for a while for some reason.
Today I gained access of it again....seems someone fixed the problem.
About X2.1....I ported the bootloaders for both FMU…"
"Wow, the power supply is not good...too much noise? I hope when you apply a clean power the RC noise will be reduced too. Also do avoid connecting something noisy ( like servos ) to the receiver."
"Disconnect everything but power, ESCs, receiver and GPS.....no camera, no servos, no video Tx....
Make a clean setup and calibration and make a fresh log."
Make a clean setup and calibration and make a fresh log."
"Hi Marcell,
Please provide your wiring, connected devices, firmware installed, settings and log files if any.
BR
Nick"
Please provide your wiring, connected devices, firmware installed, settings and log files if any.
BR
Nick"
"That's normal...safety switch will be excluded later."
"Hi Yana,
If you're using Windows, you will see it as Pixracer when you click on your Internet access connections, just click Connect and if asked for pass, type pixracer.....that's all.
Additional info here - https://pixhawk.org/peripherals/8266"
If you're using Windows, you will see it as Pixracer when you click on your Internet access connections, just click Connect and if asked for pass, type pixracer.....that's all.
Additional info here - https://pixhawk.org/peripherals/8266"
"Hi guys,I noted a strange behavior of MP 1.3.39 when flashing a Pixracer....no microSD inserted!I just selected Initial Setup -> Install Firmware -> APM: Copter V3.3.3 After downloading the firmware, MP asks you to "Unplug the board, click OK, then…"
"Hi Kim,
You can freely place your order at auav.co and we can deliver it to any point of the world.
Best regards
Nick"
You can freely place your order at auav.co and we can deliver it to any point of the world.
Best regards
Nick"
"Ya....the Chunese guys are either too hungry or have mice in their IC stores.... :-)"
"Hi Mike,
This is the initial batch of 100pcs of a kind. We already started testing them and it seems everything is going fine. Next week we'll announce these devices with prices at auav.co
BR
Nick"
This is the initial batch of 100pcs of a kind. We already started testing them and it seems everything is going fine. Next week we'll announce these devices with prices at auav.co
BR
Nick"
Hi guys,AUAV Co. team is proud to announce two new useful gadgets - an I2C AIRSPEED sensor and 3.3/5V UNIVERSAL I2C HUB.The newly designed AIRSPEED sensor now incorporates JST GH connector + additional solder pads on the bottom side, and 5V->3.3V…
"Hi Jure,
Do you use Hall sensors for rotor positioning?
BR
Nick"
Do you use Hall sensors for rotor positioning?
BR
Nick"
"Hi Thorsten,
The ESP-01 ( normal one ) works just fine. Btw, we'll design out own ESP module with hardware flow control, based on ESP-06
Nick"
The ESP-01 ( normal one ) works just fine. Btw, we'll design out own ESP module with hardware flow control, based on ESP-06
Nick"
"Hi guys,
Unfortunately the first regular batch will be delayed because of the cable sets delay. I hope we'll receive the cables around Jan 4-5th. Currently, the boards tests are in progress. Will keep you informed.
Best regards and Happy New Year !"
Unfortunately the first regular batch will be delayed because of the cable sets delay. I hope we'll receive the cables around Jan 4-5th. Currently, the boards tests are in progress. Will keep you informed.
Best regards and Happy New Year !"
