About

Gender

Male


Location

Saxonburg, PA


About Me:

Recently retired and starting to enjoy my free time.


Please tell us a bit about your UAV interest

Just got into building and flying FPV and photo platforms. Started with an AR Drone, then to DJI F450 with Boscam FPV setup, to Tarot fy690s which I'm building now for water sampling platform.


Hometown:

Saxonburg, PA


Activity Feed

Russell Stutzman replied to Stijn Debecker's discussion I2C splitter problem
"Does this happen on USB only or with the battery connected? I found that too many things on the I2C bus while powering with only USB caused this for me. Once hooked up to the battery all of the problems went away."
Oct 14, 2015
Russell Stutzman replied to Paul Hunt's discussion Internal Compass not showing up
"After you complete calibration does it give you two sets of offsets? I know when I calibrate mine the second one barely seems to follow but I get two sets when completed.
You could try removing your external and try calibration again and see what…"
Aug 6, 2015
Russell Stutzman replied to Butch Canares's discussion Yaw and Throttle mixed up
"I had this happen with an update to Mission Planner 1.1.29. An update to 1.1.30 set things back to normal for me.  Something to check anyway."
Jul 13, 2015
Russell Stutzman replied to sturgessb's discussion Low KV X8 configuration, cant get it tuned :(
"Your setup in ecalc predicts 69% throttle at hover. I don't think you have enough propeller surface for that low kv of a motor. Change to even a 330kv ups you to 47% throttle at hover by eCalc's results.
Your current setup doesn't allow for a lot of…"
Jul 10, 2015
Russell Stutzman replied to Randy's discussion Copter-3.3 beta testing
"What GCS are you using? Have you tried a different one? I would think more copter would be having problems with such a basic setting. Maybe it is the GCS that isn't properly doing what you expect. I noticed in a quick Google search that something…"
Jul 6, 2015
Russell Stutzman replied to airmazingvideo.com's discussion Throttle and Yaw channels switch places after upgrade Mission Planner 1.3.29
"I had that happen also. There is a newer update that corrects it. 1.3.30."
Jun 26, 2015
Russell Stutzman replied to Michel Kosloff's discussion Getting "No GPS" instead of "No Fix" in MP
"The APM uses a 5 pin plug and the Pixhawk uses a 6 pin plug. I didn't realize this right away as the 5 pin plug went into the 6 pin connector on the Pixhawk but the GPS was problematic. After changing to a 6 pin wired correctly the GPS worked as…"
Jun 15, 2015
Russell Stutzman replied to Mr Flying Pizza's discussion Fool proof guide for newbies to avoid flyaways or disarm problems?
"I believe the calibration/initialization is finished after the LED quits flashing red-blue. Once I plug my power in I leave the aircraft set until I get my GPS lock.
RTL is fine to use just be ready to switch to a non GPS mode should your aircraft…"
Jun 8, 2015
Russell Stutzman replied to Mr Flying Pizza's discussion Fool proof guide for newbies to avoid flyaways or disarm problems?
"Use due diligence and learn about your aircraft and it's control systems before you fly it. Learn how to fly your aircraft in non-GPS flight modes like stabilize and alt hold before using GPS modes.
Make sure your aircraft is sitting level and still…"
Jun 8, 2015
Russell Stutzman replied to Benjamin's discussion Pixhawk shoots straiht up
"http://copter.ardupilot.com/wiki/configuration/arducopter-parameter...
Pilot maximum vertical speed (ArduCopter:PILOT_VELZ_MAX)
The maximum vertical velocity the pilot may request in cm/s

Range: 50 500
Increment: 10
Units: Centimeters/Second"
Jun 4, 2015
Russell Stutzman replied to Chuck Spaulding's discussion Aux Out
"It may be possible and hopefully someone else with more knowledge can jump in. I know the improvements to the Pixhawk are constant so what doesn't work right now may work soon."
May 16, 2015
Russell Stutzman replied to Chuck Spaulding's discussion Aux Out
"Two ways come to mind. Directly from the receiver bypassing the Pixhawk or dedicated receiver and second transmitter and don't forget second operator. "
May 16, 2015
Russell Stutzman replied to weiqiang's discussion What does the mean about fence setup parameters
Jan 11, 2015
Russell Stutzman posted photos
Dec 19, 2014
Russell Stutzman replied to FlyHigh's discussion Cannot install 3.2, installation fails while reading hex
"How are you powering the board? I have had problems with a laptop not supplying enough power through the USB port. Also just for the upgrade try unplugging things from the board and retrying.

Russ"
Nov 25, 2014
Russell Stutzman replied to Dieter Rencken's discussion Strange Yaw values
"Perhaps you were facing north and your yaw values were bouncing between 0 and 360 degrees. That would show up as big jumps as you see but was only 1 or 2 degrees or so of actual yaw.

Russ"
Nov 2, 2014
More…