Gender
Male
About
Location
Novosibirsk
About Me:
Doctor from Siberia
Please tell us a bit about your UAV interest
I just want to make the flying cam, no special drones or pilot interest.
Hometown:
Shenzhen, China
Activity Feed
"Got the same issue trying to download log via mavlink. MP 1.3.30, APM 2.5, firmware 2.x (cannot see exactly thru MP). Have downloaded logs week before with absolutely the same setup - successfully."
"So how does it fly? Any issues?"
"MP cannot load previous firmware list. I don't know if this happen because firmware generator site is not working, or there's a MP bug. So one can go directly to http://firmware.diydrones.com/Copter/ , download appropriate .hex and open it in…"
"Just reflashed. Than checked current flight mode and disabled pre-arm check."
"Now arming ok on 3.1.2 too, after reflashing back again. Still don't know what has this been. Maybe the wrong flight mode? I believe I checked it at the first time..."
"Well, just have armed successfully with an early version hex of May 2013. Current is still unarmable."
Hello there)I've recently changed firmware v2.8 to 3.1.2, calibrated radio and accelerometer, and APM is not arming anymore. I also change ESC's to HK's Simonk, but everything else, including radio and its settings stay same. Red flashes withsingle…
"Due to COG shifted forward, rear engine might be facilitated: lesser motors and props. What do you think people: will that work?"
"I think it's possible. Just compare your flight 2500 mAh battery and AA rechargeables with the same capacity. About 10 times smaller and lighter, yes?
So, we just need more discharge rate from these AA's - to put them in parallel. As much as…"
So, we just need more discharge rate from these AA's - to put them in parallel. As much as…"
"Many thanks Michael! With new version and new interface the bug appear no more. I've checked out again this and previous - it was and now it is not."
"Michael, this again makes me think that modern UAV world is only for lucky people. Confusing, yes.
As for me, I had at least three battery-dependent crashes. After two of them, there appeared to be a cell with no power and maximum resistance. Just a…"
As for me, I had at least three battery-dependent crashes. After two of them, there appeared to be a cell with no power and maximum resistance. Just a…"
"I've tried to upload 3DR-Ublox.txt to Crius v2.0, but got errors like this:
Sending: CFG-PRT - B5 62 06 00 14 00 01 00 00 00 C0 08 00 00 00 96 00 00 07 00 01 00 00 00 00 00 81 84 ...... timeout occurred without receiving an answer. Retrying...!…"
Sending: CFG-PRT - B5 62 06 00 14 00 01 00 00 00 C0 08 00 00 00 96 00 00 07 00 01 00 00 00 00 00 81 84 ...... timeout occurred without receiving an answer. Retrying...!…"
"I'd have 2 battery inputs in parallel. Batteries are likely to die whenever they want, and it's a sorry to kill such a rich board in that battery-dependent accident. Another battery in parallel mode will give you enough insurance."
"BTW, what is '3DR driver' installed by MP? What is it supposed for and can it be replaced with another driver?"
Crash description: no network connections displayed in status bar. Cannot enter network connections either from start menu or control panel. After this Explorer stops and doesnt restart. Cannot use Windows. (despite, there's still wifi and…
Solved by changing PC and USB port. 4 of 6 ports caused this error.Mission Planner 1.2.53 (latest)APM 2.5.2OS: Windows XPAll drivers downloaded, installed and checked just before the test. APM moved to COM4.After uploading different firmwares got…
