Gender
Male
About
Location
Medford, MA
About Me:
I have some experience with electronics, Arduino & DIY.
Please tell us a bit about your UAV interest
Looking to get into aerial photography.
Hometown:
Boston
Activity Feed
"If you can get a receipt of the original purchase, your homeowners insurance might cover it.
Good luck."
Good luck."
"Looked good earlier. Currently I'm getting a 500 internal server error.What is Sky Cover? How of your sky the satellites cover?"
"Nice work. Keep us posted when you have time."
"Just to add my thanks. Great job on 3.2 everyone.
Tried Alt Hold, Stabilize, Loiter on my Iris today and it worked great."
Tried Alt Hold, Stabilize, Loiter on my Iris today and it worked great."
"Good luck, looks interesting. What size motors will you use?"
"Thanks for the new release, looks great.
@hughes I went through a similar thing and gave up. I just pull up where I'm going to fly while in my house. I leave it open and my Nexus 7 on, even if I then have to drive 45 minutes to get to the where I…"
@hughes I went through a similar thing and gave up. I just pull up where I'm going to fly while in my house. I leave it open and my Nexus 7 on, even if I then have to drive 45 minutes to get to the where I…"
"Nice job devs and testers. Thanks for giving us such amazing firmware."
"Sounds like you have the wrong baud rate.
Also you can remove the SD card from Iris and get the logs from the card."
Also you can remove the SD card from Iris and get the logs from the card."
"Still seeing lousy flight times, probably due to weight. Flip with no battery weighs 3.3 lbs compared to Iris which weighs 2.2 lbs.
I do I have an extra small battery in front as a weight to compensate for lack of gimbal, which I plan on adding.…"
I do I have an extra small battery in front as a weight to compensate for lack of gimbal, which I plan on adding.…"
"Fixed the voltage issue. Replaced cable from 3DR Power module to power on Pixhawk.
Ground wire had come loose."
Ground wire had come loose."
"Voltage and current measuring not ok.
Hooking the quad to apm and adding a 3.5 mAh battery at 12.45 v gets readings of .2 or .3v .
If I try to adjust this under Battery Monitor/ Advanced Settings/ Measure Battery Voltage and put 12.45 I then get…"
Hooking the quad to apm and adding a 3.5 mAh battery at 12.45 v gets readings of .2 or .3v .
If I try to adjust this under Battery Monitor/ Advanced Settings/ Measure Battery Voltage and put 12.45 I then get…"
"Voltage seems ok. Had a look at at my ESC settings and they seem ok too.
I did change the battery type from Lipo to Ni-xx as recommended by this page.
I have another quad and will try the same battery in both of them this weekend to see if it is…"
I did change the battery type from Lipo to Ni-xx as recommended by this page.
I have another quad and will try the same battery in both of them this weekend to see if it is…"
"Thanks Nathaniel.
No, I hadn't seen that video. I'll try calibrating the voltage/current with a freshly charged battery and see what happens.
I'm using a Turnigy Accucell 6 and balance charging the batteries.
Todd"
No, I hadn't seen that video. I'll try calibrating the voltage/current with a freshly charged battery and see what happens.
I'm using a Turnigy Accucell 6 and balance charging the batteries.
Todd"
"Thanks for looking Nathaniel.
One battery is about 6 months old and one is about 3 months old.
Attached are the parameters.Flip-Params"
One battery is about 6 months old and one is about 3 months old.
Attached are the parameters.Flip-Params"
Hi,Just finished building a Flip FPV Pro G but have no gimbal yet, but have added some weight to compensate. The Flip could use a little more tuning but flies fine.Flip FPV Pro GPixhawk running 3.15MT2216 900Kv Tiger motorsSkywalker 25A Quatro 4 in…
