About

Gender

Female


Location

islamabad


About Me:

undergraduate communication system engineering student


Please tell us a bit about your UAV interest

Applications of RC quadcopter in FYP Automation of rc quadcopter


Hometown:

islamabad


Activity Feed

enya replied to enya's discussion Quadcopter Firmware V3.1.4 in Learning to program the Ardupilot Mega
"yes, got that, thankyou."
May 14, 2014
enya posted a discussion in Learning to program the Ardupilot Mega
Hello I have V3.1.4 firmware in my quad copter which i downloaded via mission planner. it is a hex file. I want to understand the code, from where i can get the code written in C? as different forums suggest that if you convert hex file into…
May 13, 2014
enya replied to Randy's discussion ArduCopter-3.1 released!
"Hello, i have v3.1.4 in my Quadcopter's APM 2.0. i want to understand the code and for that i need to open sourcecode in arduino software, how can i do that?"
May 10, 2014
enya replied to enya's discussion Firmware for APM 2.0
"thankyou for replying. :)"
Apr 27, 2014
enya posted a discussion
Hello, i am using APM 2.0 for my quadcopter. i have downloaded the mission planner from APM site but now as the manual says, when i have to choose the motors layout, (i have plus configuration) but the mission planner isn't showing any option for…
Apr 23, 2014
enya replied to enya's discussion controlling motor speed using APM 2.0 in Learning to program the Ardupilot Mega
"I have tried to use the same code as i used in Arduino uno, attaching only 1 motor, but the problem is coming that as soon as i run the program, power supply with which ESC have been connected, immediately starts blinking rapidly showing that…"
Apr 21, 2014
enya replied to Oliver Buhn's discussion Ardupilot source code before APM_HAL in Learning to program the Ardupilot Mega
"i have APM 2.0, so i'm guessing i can't load firmware 2.8.1 in it.? and i want to customize the code which i would load in it."
Apr 16, 2014
enya replied to Oliver Buhn's discussion Ardupilot source code before APM_HAL in Learning to program the Ardupilot Mega
"i have same question."
Apr 16, 2014
enya posted a discussion in Learning to program the Ardupilot Mega
Hello, for a startup, i just want to control the speed of 4 BLDC motors using APM 2.0. which i previously controlled using arduino uno, can anyone help?
Apr 15, 2014
enya replied to enya's discussion APM 2.0
"i read it here that it requires a GPS module for automatic flight.
http://copter.ardupilot.com/wiki/introduction/what-you-need/
if it is already on board why would they place a picture of it separately? O.o"
Apr 13, 2014
enya posted a discussion
I'm going to use APM 2.0 for my quadcopter, i just want to fly quad using RC that is autonomous flight is not required, so does that mean i do not need to buy GPS module that is otherwise essential for automatic flight?
Apr 13, 2014
enya posted a discussion
Hello!I want to use APM 2.0 for my quadcopter but i want to get it from hobbyking , as i dont have enough budget to get the original one from 3drobotics but it read in a post that the official 3D Robotics APM 2.0 board has a unique signature and the…
Feb 12, 2014
enya posted a discussion in ArduCopter User Group
In APM 2.6 mission planner is used to give way points, what i understand from it is that there is a GUI by which you give way points and then copter reaches at those points autonomously. what i don't understand is that how these waypoints which you…
Dec 26, 2013
enya posted a discussion
My project is design and fabrication of RC stabilized quadcopter, the quadcopter will stabilized autonomously (stabilization will be handled by the flight controller board) and then the orientation/flight of copter will be controlled by RC…
Dec 26, 2013
enya replied to auzi's discussion PIC18F pwm signal to RC ESC for control brushless motor..need help.
"I have the same query. i have turnigy plush 18-A ESC and the manual that comes with it suggests that it directly takes commands from RC transmitter and it needs to be attached with the receiver. however i want to use it in quadcopter so can i…"
Dec 16, 2013
enya replied to David's discussion ESC programming
"Can i use the controller on the flight control board for doing PWM for ESC's instead of attaching a separate programming card with each ESC that i use? i intend to program ESC with controller on my flight control board that will get commands from…"
Dec 16, 2013