About

Gender

Male


Location

Alor Setar, Kedah


About Me:

Active in RC for the past 30 years, recently into UAV and micr ocontroller


Please tell us a bit about your UAV interest

tried building tricopter using gyro only, need to have board controller for better performance


Hometown:

Alor Setar, Kedah, Malaysia


Activity Feed

nubli hashim commented on Benoit Pereira da Silva's blog post Birth of a drone
"any video of the off spring guys?"
Jul 18, 2014
nubli hashim commented on Crispin's blog post Spektrum DX8 and AR8000 Failsafe setup
"just wonder if same setup will work on my futaba 9c? thanks in advance"
Dec 24, 2013
nubli hashim replied to elad orbach's discussion my diy ground control station
"nice job dude"
Dec 19, 2013
nubli hashim commented on Scott Berfield's blog post Adding External LED Indicators and a Piezo Beeper for Arm and GPS Status
"does this work on apm:plane? or just for arducopter"
Dec 16, 2013
nubli hashim replied to Randy's discussion ArduCopter-3.1 released!
"superb randy.. I will load the 3.1 fw version. can I use my channel 6 rx for auto tune? I only have 6 channel rx max to run apm, channel 5 for mode.."
Dec 15, 2013
nubli hashim replied to Randy's discussion AC-3.1 autotune support discussion
"I see the latest mission planner 1.2.89. the FW is 3.1. is the 3.1 now official? with autotune and no more beta?"
Dec 14, 2013
nubli hashim commented on Chris Anderson's blog post Latest improvements to the Mission Planner
"@Mikael, I think APM support X8 too. it's in the MP (though I am not using it yet)"
Aug 4, 2013
nubli hashim posted a discussion
Guys, I wanted to flash my APM with latest firmware, I had 3.0.1 but when I wanted to reflash. no icon to do it. the initial setup has no install software, anymore, it just pop-out mandatory hardware. that means I cannot flash in plane setup, or can…
Aug 3, 2013
nubli hashim commented on Rob_Lefebvre's blog post Royal Canadian Mounted Police use UAV and FLIR to locate lost man.
"Great! endless application of drones, in particular saving lives."
May 9, 2013
nubli hashim commented on Roberto Navoni's blog post VR GIMBAL : 3 Axis 32bit Direct Drive Gimbal is coming!
"I just bump into this thread.. been dying to ask if somebody would add source dode for brushless gimbal. can't we just add codes without any new added gadjet? not possible isn't it?"
Apr 28, 2013
nubli hashim commented on Xerravon's blog post 6 positions for Futaba 9C Super
"ok guys. I got the solution. Follow Eric Thomas setting. exactly.
here's how I do it.::
Firstly go to ordinary screen. push left top button to enter programming. go to page 2/2. set aux channel 5 to switch C. then push bottom left button to confirm…"
Apr 13, 2013
nubli hashim commented on Dries Raymaekers's blog post ArduPlane flies at 4500m altitude
"Fantastic, and well done, congratulation to the team. APM is put into good use for people around the world. bravo"
Apr 10, 2013
nubli hashim commented on Xerravon's blog post 6 positions for Futaba 9C Super
"same thing goes to me only position 1,3,6 highlighted, 2,4 not working, wonder why"
Apr 9, 2013
nubli hashim replied to Marco Robustini's discussion ArduCopter Heavy X-Octo / X8 Coax - Foto, video and other
"nice sharing buddy. following eagerly"
Mar 5, 2013
nubli hashim replied to Randy's discussion ArduCopter 2.5 released!
"great job guys.. simply gret"
Mar 25, 2012
nubli hashim commented on Roberto Navoni's photo
"nice bro.. would you like to share some set-up and dimensions info on the quad.. "
Mar 24, 2012
More…