Robert Baumgartner
  • Male
  • São Paulo
  • Brazil
Share

Robert Baumgartner's Groups

Robert Baumgartner's Discussions

Quadcopter Drifting in pos-hold after 10 minutes of flight

Started this discussion. Last reply by Robert Baumgartner on Wednesday. 2 Replies

Hi,I am flying with arducopter in my multicopters more than 5 years, and this is the first time I can’t solve the problem by myself.The problem is: after 8 or 9 minutes flying in pos-hold mode, my…Continue

 

Robert Baumgartner's Page

Latest Activity

Robert Baumgartner replied to Robert Baumgartner's discussion Quadcopter Drifting in pos-hold after 10 minutes of flight
"if everybody doesn’t know and can' t help, I have a real problem.   This is the reason for everybody starts to buy RTF drones, nobody helps."
Wednesday
Armin Strobel replied to Robert Baumgartner's discussion Quadcopter Drifting in pos-hold after 10 minutes of flight
"Sounds like your heading is drifting away."
Tuesday
Robert Baumgartner posted a discussion

Quadcopter Drifting in pos-hold after 10 minutes of flight

Hi,I am flying with arducopter in my multicopters more than 5 years, and this is the first time I can’t solve the problem by myself.The problem is: after 8 or 9 minutes flying in pos-hold mode, my quad start to drift in circles. And the circles are bigger and bigger. After this when I correct using the Stick, and after a few seconds the circles starts again.But the stranger thing is, in the beginning of the flight pos-hold is “Rock solid”.The setup is:Raspberrypi3 + Navio2 board with arducopter…See More
Tuesday
Robert Baumgartner replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in the group Pixhawk 2 User Group
"They will fix for me, thanks for 3dxr.co.uk really professional."
Apr 16

Developer
Philip replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in the group Pixhawk 2 User Group
"This exact same post is on so many sites, it’s difficult to answer them all. If your board is broken, RMA it via your local distributor The glue is added to increase support for this connector as so many people are forgetting to use the…"
Apr 13
Robert Baumgartner replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in the group Pixhawk 2 User Group
"Problems always happen, the difference is how to manage then, I already send a E-mail to info@3dxr.co.uk, let’s see.   Thanks"
Apr 13
eko rahardjo replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in the group Pixhawk 2 User Group
"Mine is breaking..no glue at all.. the bad news led pad is broken  and imposible to re-solder. This happen when i remove gps connector. Very fragile.  Pay attention on GPS1 connector.. why there is a hole  exactly on  gps1…"
Apr 13
Kelly Schrock replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in the group Pixhawk 2 User Group
"The glue is normal, as Thomas said. It was added to reinforce that connector. The connector is a "pinch to release" type, but it's so close to the Cube it's impossible to pinch. So people tend to push on the tab to release it,…"
Apr 12
Thomas Stone replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in the group Pixhawk 2 User Group
"Hi Robert,  The glue on the GPS1 connector is normal. It strengthens the GPS1 connector.  However, the "No GPS" message is not normal. You should contact your distributor/vendor to see if the unit is defective. They will be able…"
Apr 12
Robert Baumgartner added 2 discussions to the group Pixhawk 2 User Group
Apr 12
Robert Baumgartner replied to Robert Baumgartner's discussion Pixhawk + Here+ - With Rover stand alone in the group Pixhawk 2 User Group
"yes, thanks a lot."
Apr 12
Kelly Schrock replied to Robert Baumgartner's discussion Pixhawk + Here+ - With Rover stand alone in the group Pixhawk 2 User Group
"Ah, yes, I would get out into an area where you're certain not to have interference from buildings and whatnot and try there. The Here+ is pretty good at getting satellite reception near my house in a yard with trees, but those structures…"
Apr 12
Robert Baumgartner replied to Robert Baumgartner's discussion Pixhawk + Here+ - With Rover stand alone in the group Pixhawk 2 User Group
"much more than 2 minutes, always "No GPS" (when I use only the Rover ), but I will do the tests again in other place, I´m really close too big buildings , then I can ensure if is a problem or not.   I´m using Mission…"
Apr 12
Kelly Schrock replied to Robert Baumgartner's discussion Pixhawk + Here+ - With Rover stand alone in the group Pixhawk 2 User Group
"Does this condition persist for very long after you power up? With my Here+, I usually have a fix within 2 minutes of powering it up, usually much sooner than that. Until then you'll of course get a "No GPS" or "NoFix"…"
Apr 12
Robert Baumgartner replied to Robert Baumgartner's discussion Pixhawk + Here+ - With Rover stand alone in the group Pixhawk 2 User Group
"thanks, but when I on turn on the Drone + Rover stand alone (without the base) , I have "No GPS" status, thats why I asked. "
Apr 12
Kelly Schrock replied to Robert Baumgartner's discussion Pixhawk + Here+ - With Rover stand alone in the group Pixhawk 2 User Group
"You can, but not if you want RTK correction data to be sent to the vehicle. If you're not using the base station, you'll just be using a normal 3D fix."
Apr 12

Profile Information

About Me:
CIO in a TI company
Please tell us a bit about your UAV interest
Hobby
Hometown:
São Paulo

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2018   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service