Tobias
  • Germany
Share
  • Blog Posts
  • Discussions (12)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Tobias's Discussions

Advice needed: how to mount a Raspberry pi camera module jello free?

Started this discussion. Last reply by james Jun 13, 2018. 3 Replies

Hi,I have build a small quadcopter which I want to use for low quality/high risk mapping tasks. Unfortunately the Raspberry Pi camera shows extreamly high jello, there are serveral horizontal stripes…Continue

Tags: jello, camera, Pi, Raspberry

Is the antenna of this Drotek Neo m8t module damaged or is that a normal condition for a new product

Started this discussion. Last reply by Tobias May 17, 2018. 1 Reply

Hi,I have ordered an uBlox neo m8t module at Drotek. It arrived yesterday in the condition depicted below (the right one). I think that is not acceptable since the other module (the left one) has not…Continue

SIK Radio V2: rx/tx signal sniffing when connected via usb

Started Sep 4, 2016 0 Replies

Hi,I want to connect my telemetry radio via USB to my NAVIO2. At the same time I want to use a Teensy with the MavLink_FrSkySPort-Library to transmit telemetry data to my Taranis.I do not want to use…Continue

Tags: radio

 

Tobias's Page

Latest Activity

Tobias replied to DR WHO's discussion pixhawks DEAD don't buy
"Interesting claim.  I have been flying last year for more than 100 h (in air time) and mapped more than 1.500 ha with diy copters bulid from cheap china stuff as well as mRo autopilots and I have never experienced a single flyaway. I had some…"
Jan 9
Tobias commented on Phillip Kocmoud's blog post Introducing the AUAV X2.1 Flight Controller
"Hi, I'm only using 2 compasses. I had no further problems after solving the initial orientation problem. I think the best is to check the orientation of each compass when all other compasses are deactivated. Arducopter 3.6 should improve the…"
Nov 6, 2018
Tobias replied to Carlos Whale's discussion How to avoid malicious anti-drone system?
"This discussion started with the question how to avoid "drone defender", a jammer only available to authorities. Did you read the  question? Its not about general strategies to handle gnss loss. Its about continuing a mission if gnss…"
Nov 3, 2018
Tobias replied to Carlos Whale's discussion How to avoid malicious anti-drone system?
"I don't get your argument. Anyhow, I don't see why anyone should try to avoid jamming with diy methods which are lacking extensive testing. Someone who does that is simple not acting responsibly. I don't see what is bad about beeing a…"
Nov 3, 2018
Tobias replied to Carlos Whale's discussion How to avoid malicious anti-drone system?
"I think one of the scenarios where a drone would meet a jammer is when delivering drugs, weapons and phones to prisons. Or delivering explosives to protected areas. I don't think it has something to do with censorship if people who know how to…"
Nov 3, 2018
Tobias replied to Carlos Whale's discussion How to avoid malicious anti-drone system?
"I wonder way there should be a legal scenario to awoid such a jammer. Either this jammer is used by the state authorities and it is illigal to fly there, or the jammer is used illegally and you should report the use of the jammer to the state…"
Nov 2, 2018
james replied to Tobias's discussion Advice needed: how to mount a Raspberry pi camera module jello free?
"Hope you will get good results with the isolation. Appreciate any update"
Jun 13, 2018
Tobias replied to Tobias's discussion Advice needed: how to mount a Raspberry pi camera module jello free?
"I will try to isolate the battery and the camera together against vibrations and hope the weight of the battery will do the job. I had not had the time to try it yet."
Jun 12, 2018
james replied to Tobias's discussion Advice needed: how to mount a Raspberry pi camera module jello free?
"Howdy! How's your research so far? Found a trick to clear those horizontal stripes?"
Jun 12, 2018
Tobias posted a discussion

Advice needed: how to mount a Raspberry pi camera module jello free?

Hi,I have build a small quadcopter which I want to use for low quality/high risk mapping tasks. Unfortunately the Raspberry Pi camera shows extreamly high jello, there are serveral horizontal stripes going through the picture.Has anyone experience how to mount the camera? I have used some gel pads, but I guess the camera is to light.Thx, TobiasSee More
May 31, 2018
Tobias commented on Phillip Kocmoud's blog post Introducing the AUAV X2.1 Flight Controller
"I have mapped 370 ha in the last days with strong wind (>10m/s).  I started my new build without any previous test flight and was not able to atutune it. Anyhow, Arducopter and the X2.1 managed to handle 24 flights/10 hours of total flight…"
May 30, 2018
Tobias commented on Phillip Kocmoud's blog post Introducing the AUAV X2.1 Flight Controller
"Hi Andreas, with Arducopter 3.5 it did not work out of the box but crashed on first take-off destroying 2 T-Motor CF props ;-(. My fault because I'm under pressure to finish the maschine to go mapping and skipped some in depth testing. With…"
May 22, 2018
Tobias commented on Phillip Kocmoud's blog post Introducing the AUAV X2.1 Flight Controller
"Hi Phillip, actually I'm having trouble now to figure out how to configure the orientation correctly. I figured out dad I have to change the BRD_TYPE parameter to 20 but the compass is still pointing in the wrong direction. I will give…"
May 22, 2018
Tobias replied to Alex's discussion AHRS_ORIENTATION and COMPASS_ORIENT
"Did you solve that problem? I want to do the same."
May 21, 2018
Tobias replied to Tobias's discussion Is the antenna of this Drotek Neo m8t module damaged or is that a normal condition for a new product
"Any opinions?"
May 17, 2018
Tobias posted a discussion

Is the antenna of this Drotek Neo m8t module damaged or is that a normal condition for a new product

Hi,I have ordered an uBlox neo m8t module at Drotek. It arrived yesterday in the condition depicted below (the right one). I think that is not acceptable since the other module (the left one) has not the same scratches, marks and is not dirty as this one. I also have several modules from mRobotics which where not delivered in such conditions.Drotek refuses to acknowledge that the module is in bad condition. What do you think about the condition and should I return it or not? …See More
May 16, 2018

Profile Information

Please tell us a bit about your UAV interest
Aerial mapping, peatland science
Hometown:
Greifswald, Germany

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service