Gender
Male
About
Location
Adelaide, South Australia
About Me:
Modelling and electrons interests
Please tell us a bit about your UAV interest
For electric power model air-craft
Hometown:
Adelaide
Activity Feed
"Hi Mirko,
I have resolved the problem by doing the build on a Ubuntu System instead of my Windows 7 system.
Regards David"
I have resolved the problem by doing the build on a Ubuntu System instead of my Windows 7 system.
Regards David"
"Hi Mirko,
I am using the latest installation instructions to rebuild my BBBmini and I get to step 23 and it fails. " ardupilot,git " does not appear to be in the Github any more?
Were has it gone?????
Regards, David Leigh"
I am using the latest installation instructions to rebuild my BBBmini and I get to step 23 and it fails. " ardupilot,git " does not appear to be in the Github any more?
Were has it gone?????
Regards, David Leigh"
"Hi,
I had the same problem on Friday. This was resolved when I plugged in the BBBmini cape into the BeagleBone.
Then the Quad was fully operational.
David"
I had the same problem on Friday. This was resolved when I plugged in the BBBmini cape into the BeagleBone.
Then the Quad was fully operational.
David"
"Hi Mirko,
I have used the latest Software build instructions to build code for my Quad and it is operational.
I would like to build code for my HEXA. The previous instructions on how to do this don't
work with this updated version of software. …"
I have used the latest Software build instructions to build code for my Quad and it is operational.
I would like to build code for my HEXA. The previous instructions on how to do this don't
work with this updated version of software. …"
"Hi Mike,
I am using a telemetry link when I see the difference in GPS status
David"
I am using a telemetry link when I see the difference in GPS status
David"
"Hi Mirko,
I have seen a difference in what happens to MISSION PLANNER display on GPS status between the output of a PIX-HAWK and the BBBmini. Normally the GPS status shows a GPS module is present on connection to MISSION PLANNER.
With connection of…"
I have seen a difference in what happens to MISSION PLANNER display on GPS status between the output of a PIX-HAWK and the BBBmini. Normally the GPS status shows a GPS module is present on connection to MISSION PLANNER.
With connection of…"
"Hi Mirko,
Has support for the COMPASS with I2C been considered. I believe that is required for proper operation.
Regards
David"
Has support for the COMPASS with I2C been considered. I believe that is required for proper operation.
Regards
David"
"Hi Randy,
Thanks for the Sonar setup information. The sonar is now working on the HEXA with APM 2.6.
I am trying to download logs to see how it is working but I keep geting " LOG TIMEOUT" after a short time.
How can I tackle the this problem. …"
Thanks for the Sonar setup information. The sonar is now working on the HEXA with APM 2.6.
I am trying to download logs to see how it is working but I keep geting " LOG TIMEOUT" after a short time.
How can I tackle the this problem. …"
"Hi Randy
Mission planner would not allow me to enable my sonar.
How do you configure a MB1240 sonar unit in the beta software rc7
Regards David."
Mission planner would not allow me to enable my sonar.
How do you configure a MB1240 sonar unit in the beta software rc7
Regards David."
Hi,I am have problems with several items in the new Mission planner.When I attempt to load new firmware I am getting verify errors reported from the APM 2.5 board.When I connect an exsisting working APM 2.5 board the Mission planner reports:(a) Bad…
When using the Mission Planner to fly a task I monitor the HUD screen carefully.I have just found out the RSSI reading on the HUD does not show the actual value of the RSSI when flying it only shows 99% or 0% when signal is lost. When I play…
"Have loaded Version 8.2.2 on my NEXUS 7 tablet. Application is running with 3DR link.
Yet to try a flight with my Easy Star test bed."
Yet to try a flight with my Easy Star test bed."
"I agree with Enigma the KMZ conversion are not working as well as they used to.
My outputs are 400 meters higher than they should be making it hard to view the paths as well the other function not working any more.
David Leigh"
My outputs are 400 meters higher than they should be making it hard to view the paths as well the other function not working any more.
David Leigh"
"Hi,
Sorry I Missed out on firmware version. Both on Arduplane version 2.66 and version 2.7 using different hardware boards.
Regards David"
Sorry I Missed out on firmware version. Both on Arduplane version 2.66 and version 2.7 using different hardware boards.
Regards David"
"Hi,
I have tried it on APM 1.0, APM 2,0 and APM2.5.
And using different computers running Windows 7 and XP
Regards David"
I have tried it on APM 1.0, APM 2,0 and APM2.5.
And using different computers running Windows 7 and XP
Regards David"
Since I updated to 1.2.36 I can no longer down load data logs from the APM board.The log screen does not show any any log entries, even though terminal setup log entry said logs were in flash memory.If I load an older version of Mission Planner the…
