Hey can anyone tell me what size props came with the arducopter kit? I'm need to order a replacement, and I was going to do it from the aeroquad store, but I'm not sure what size I need?
Thanks in advance!
Read more…I have a futaba 7c tx and the throttle has the different clicks as you raise or lower the throttle. When hovering my arducopter, one notch lower doesn't provide enough lift, and the next notch up makes the copter fly upwards. Is there a way to make i
Read more…Hi to all!
I'm looking for a webpage where i can find information about brushless motors, information like:
How to obtain the best thrust vs. prop dia. vs. current consumption.
Info about the BL motor parts.
How the winding change torque, current consum
Read more…Here is the test fly video. Can anyone tell me what's wrong with my build?
Read more…
Hi all,
I'm using the configuration shown in this setup: IMG_4778.jpg
I've uploaded the firmware 1.8.2 to the ArduIMU v2 and I have configured the ArduIMU according to the manual (http://code.google.com/p/ardupilot/wiki/ArduIMU). When I connect the F
Read more…Hello All,
I've searched around, and found a lot of discussions on the MTEK GPS and APM.
I've tried everything I know to try, and am at a dead end.
I have the MTEK with NO BATTERY. I successfully reflashed the unit by soldering pins onto it, and hoo
Read more…Currently I am doing on the arducopter and I have encountered some problems about the programming part.
Firstly, how do I vary the PID values for my quadrotor?
I have found certain lines in the programming, is it changing this to do? (I am using stabl
Read more…Is it bad to charge batteries in the cold? I mean something like outside where it's like mid 30's. Or what is considered too low for charging temperature wise?
Read more…
If I use xbee telemetry at 900 Mhz.
Can I, or is it possible to use a multi channel 900Mhz Video Tx/Rx system along side it without conflict?
As the video has numerous channels I should be able to find one that doesn't interfere with the telemetry, sh
Read more…Hi, does anyone have any input on the idea of using a ardupilot mega with magnometer( complete AHRS) to stabilize a 3 axis camera gimbal with continous rotation servos? No GPS required for this idea, just wanting to use the "Fly By Wire" capability o
Read more…First off im new to all of this so please excuse me if im asking a dumb question.
I have an RTK GPS I use for my archaeological work. Is it possible import a GGA string from the RTK data into the APM? GPS_PROTOCOL_NMEAAP_GPS_NMEA is available in th
Read more…Hi all,
in order to load code into Ardupilot I have to perform the following steps:
- connect FTDI cable to computer
- connect FTDI cable to ardupilot
- power on ardupilot
- open arduino
Is there a "correct" sequence in which I should perform the above s
Read more…I thought I read somewhere that an update would be out shortly (2 weeks ago) - Any word on when this might happen? Looking forward to using all the sensors - I know the version in the truck has this but I can never get the trunk version to work corr
Read more…I saw this thread where "HappyKillmore" has added support for an "APM binary stream". So this might mean additional fun stuff for Arducopter pilots in the future: http://www.diydrones.com/profiles/blogs/hk-gcs-now-supports-apm-binary?commentId=70584
Read more…Hi all,
I'm using Arduimo V2 flat. I've downloaded the latest code (1.8.2) from the website and connected the board through the FTDI cable. I succesfully used this FTDI cable to load code onto the Ardupilot board. I double checked that the same board
Read more…
I purchased 2 of the new DIY Drones Rev 1.1HMC5843 boards back in late NOV.
The data I'm get from them seems to have way too much "jitter".
With the magnetometers stationary and flat and level:
unit 1's readings vary by 54 count in X, 57 counts in Y
Read more…Hi,
I,am trying to calibrate my transmitter values with the configurator. During calibration all is fine but it isn't saving the values. After trying a few time it seems that the values are saved.
Also if i,am trying to change values PID stable mode i
Read more…I have almost everything to build my quad, but have some design questions.
I am assuming here (and all THAT entails) that a shorter arm will result in a lower stability platform, but greater agility.
Longer arms (with in reason) will allow the craft t
Read more…
