Guidance please,One M2MPower ESC will not see the Receiver (AMP not in loop yet) - so just beeps away (Alert tone 2) - the rest armed perfectly - so I assume its faulty - will have to get another one - Agree?I have some other escs around - can you mi
Read more…Is there a ground station with working GPS location and stuff like that for arducopter? By Ground station, I mean a software version.
Read more…Everything work ok otherwise. The 4 motors run correctly, the sensors all check out.
I have a Corona digital servo that works when I plug it into the receiver or output channel 0.
On output channel 4-7 I don't get anything.
servoMotor = constrain(APM_R
How do I know what mode I am in when I use the switches for GPS hold (on/off) and acrobatic/stable mode? I have telemetry data coming in, but is there a way to display what mode I am in so I know which position of the switch is the right one? And my
Read more…Hi there. Im currently designing Autonomous Quadrotor as my final project at school. Everything was good so far until trying to find PID parameters.
I have a question and some concerns about suppyling power from Li Po's. As you know brushless m
Hi.
Hi,
just wanted to ask, how long your Code takes to upload to APM?
I haven't got any experience in that field, but uploading the code takes something like 5-10 Minutes before arduino-loader is ready with uploading.
Seems like a hell of a long time, but
Hello,
First of all I would like to say Thanks to the DIY team for such a great
product.
Quick question, I received my Arducopter just the other day, however,
it appears that my arms are missing holes for the ESC cabling to go into??
Jani, was this inte
Hello I came up with this way of installing the ESCs that I found makes for a neat tucking away of cables. Doing them one by one I noticed that by having the cabling take a natural route around the power board my routing ended up so that while an ES
Read more…Where can I find info on spec'ing out my motor/prop/esc configuration. or can someone tell me what the typical setup would be for a 24" motor to motor quadcopter carrying, camera, telemetry, video radio, etc. basically all the options for electronic
Read more…I was wondering if anyone knows what size battery is compatible with the stock motor and ESC that comes with the Dynam Hawk Sky?
Thanks!
Read more…I want to get into it, but I cannot find a place where they tell me, which parts do I need , and which ones are more recommended
I would like to get info on:
auto pilot
gps module
pc communication
etc
thankd guys
Itay
Read more…Hey folks,I understand that APM uses yaw in coordinated turns, when banking, but the airframe I am currently working on is not very stable in yaw. Comming out of a steep bank, the airplane Pivots back and forth before settling, about the yaw axis. I
Read more…I would like to build a medium sized Quad, about 24 inches motor to motor.
Digi's X-CTU utility only lets you set the buad rate up to 52600...
I need to set my xbee's baud rate to match the APM baud rate of 115200..
anyone know how to do this?
Best,
Toby
So I have a rough design of the model I want to build, who can point me in the right direction? when it is all squared away with design and components, who do I take it to to have all the parts laser cut? And can anyone recommend a good aircraft plyw
Read more…Hi guys!
This is my first post, so please take it easy on me. I received my ArduCopter this week and assembling went smoothly. I have been flying a MikroKopter Quad and a MikroKopter Octo for two year, so I'm not entirely new to the field. I'm an embe
Hey guys,
Hello, I would like to know if it is possible to connect to arduquad another board with sensors and a microcontroller running a Real Time Operating System.
Thank very much
